Emerson Water Heaters - Recent Questions, Troubleshooting & Support

0helpful
1answer

Evergrind disposer leak

The internal seals on the shaft are bad. Given the purpose of the unit you will have to deal with corrosion and seized fasteners, Then you have to locate the seals to replace them, It is easier to replace it.
11/7/2020 3:53:17 PM • Emerson... • Answered on Nov 07, 2020
0helpful
1answer

HOW TO REPAIR A LEAKY INSINKERATOR HOT WATER

What if you back the temp down to say 165 or so would that not keep the plastic from frying?
Also does that model not sit ambient until hot water is needed and is not "hot" 24/7/365 as you
stated? Just wondering.
7/18/2018 8:56:49 PM • Emerson Water... • Answered on Jul 18, 2018
0helpful
2answers

Hi, my insinkerator hot water

My unit is 3 1.2 tears old. It started to delay the flowing of hot water. Today I held the lever down until hot water came out but I noticed water leaking from inside the unit. I figured that the tank failed, and since it was over 3 years old I decided to open it up. What I found was that there is a plastic tube at the top of the unit that was very discolored and brittle which developed a crack. when I touched it it completely severed. I called the Insinkerator hotline at 1800-558-5700 and they told me that opening the unit voids the warranty. I said that it appears to be out of warranty and I needed just the plastic tube for repair. The per on on the phone said that as a one time courtesy that a new unit would be shipped to me free of charge and that I could install it myself or they will have a tech do it. I opted to do it myself. Hope this helps
7/17/2018 3:50:31 PM • Emerson... • Answered on Jul 17, 2018
0helpful
1answer

I have a industrial hot

then you must have a bad earth form the element . if you put voltage in a element that should be in water you blow it in seconds . if you want to get humidity leave it to air dry .
3/24/2018 7:11:29 AM • Emerson Water... • Answered on Mar 24, 2018
0helpful
1answer

We wanted a hot and cold water dispenser, management does not like the table model. Is there an under cabinet model that does both. Also the price for a Model HWT-F1000S, can we buy direct. I am wa

I'm not positive but insinkerator has been making these types of units for over a decade. You can buy them from amazon
1/8/2018 12:07:38 AM • Emerson Water... • Answered on Jan 08, 2018
0helpful
2answers

I dropped a piece of glass into my garbage disposal. Now, the disposal won't work. (I get a humming noise when I turn on the poswer.)

Motor is still stuck need replacement motor I’m happy to help further over the phone at https://www.6ya.com/expert/vincent_f7b7c5f4dedd2565
7/12/2015 1:40:46 AM • Emerson... • Answered on Jul 12, 2015
0helpful
1answer

How do I fix a leak at the bottom of the unit?

You have to replace disposal because it is rusted out or the bearing is leaking. http://waterheatertimer.org/How-to-repair-and-install-Garbage-disposal.html Gene Water Heater Timers Save Money If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7
6/15/2015 7:38:10 PM • Emerson... • Answered on Jun 15, 2015
0helpful
1answer

Hot water dispenser spurts

Do you have a whole house filter in the house or you on a well I’m happy to help further over the phone at https://www.6ya.com/expert/vincent_f7b7c5f4dedd2565
6/2/2015 9:30:40 PM • Emerson... • Answered on Jun 02, 2015
0helpful
1answer

Instant hot water dispenser spurts

Sounds like the temp is too high, turn down the temp the dial should be on the front of the unit
6/2/2015 6:01:36 PM • Emerson... • Answered on Jun 02, 2015
0helpful
2answers

Water Heater Repair

If steam or excessively hot water shoots out of faucets, or you hear boilding sounds inside the hot water heater, the appliance may not be shutting off at its set temperature. The job of the temperature- pressure (TP) relief valve is to release excessive pressure from steam buildup, but this valve may have been improperly installed, or it may be faulty. Either way, this condition can be dangerous, both because hot water and steam can scald people and because enough pressure could build up to rupture the water heater. Immediately turn down the water heater’s temperature setting and allow the water to cool.
3/6/2015 10:47:06 PM • Emerson Part UWL... • Answered on Mar 06, 2015
0helpful
1answer

A piece of glass fell into our e202 & now the disposal doesn't work. (It makes a humming sound when the current is turn on.) Is there a reset button? I think I got all the pieces of

There is a reset botton but this is not your problem. There is a special tool that you can spin it manually.
9/23/2014 9:46:53 PM • Emerson... • Answered on Sep 23, 2014
0helpful
1answer

Disposal will not turn off

You note a ISE 152 Point-of-use Water heater then tell us the Runs all time. Perchance did we wire them together when installing? Find an electrician that knows what they are doing to correct this. Cross wiring indicates a lack of knowledge or skill sufficient to do job and protect life and property.
9/12/2014 7:30:52 PM • Emerson... • Answered on Sep 12, 2014
0helpful
1answer

Emerson manuals

check out this site: http://evergrind.com/images/stories/spec_sheets/Evergrind-E202-Spec-Sheet.pdf and: http://www.insinkerator.com/en-us/Service-Support/Disposer-Support/Pages/Default.aspx This should help out, but remember this model is a lower end disposal and has only a 1yr warranty.
7/23/2014 1:50:01 AM • Emerson... • Answered on Jul 23, 2014
0helpful
1answer

Insinkerator hot water heater takes a long time to dispense water

It may have mineral deposit buildup on the inside. You will need to consult your maintenance manual to see how to flush the unit and clear it of deposits. You can also contact Insinkerator for the information as well. You can use vinegar to clean it just like you would a coffee pot. Take the inlet supply off and using a funnel pour the vinegar in and turn the unit on.
7/15/2014 12:56:16 AM • Emerson... • Answered on Jul 15, 2014
0helpful
1answer

How to unistall franke mythos mtx taps

Turn off the water supply from the heater and at the main water supply line outside. place a container under the sink where the flick mixer is mounted to catch the water that will come out of the lines when you undo the fittings. there should be 2 flexible braided lines coming from the mixer to the water supply lines, undo both fittings from those lines, then undo the brass nut that fastens the mixer to the sink, you may need a 10 or 12mm socket with an extension bar to get up under the sink to be able to undo the nut. there should be a metal horseshoe shaped retaining plate that holds the mixer to the sink which should come off when the nut is undone. You may or may not have to remove the flexible lines from the mixer which you should be able to sort out when you get to that point. I hope this info helps you with your problem, the info may not be exactly how I have explained but that is how most mixers are fitted or removed.
7/6/2014 10:06:35 PM • Emerson... • Answered on Jul 06, 2014
Not finding what you are looking for?
Emerson Logo

92 questions posted

Ask a Question

Usually answered in minutes!

Top Emerson Water Heaters Experts

Gil Shultz

Level 3 Expert

3464 Answers

ray gallant

Level 3 Expert

74163 Answers

Paul Carew

Level 3 Expert

3746 Answers

Are you an Emerson Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...