Element Televison & Video - Page 9 - Recent Questions, Troubleshooting & Support


clean the jack on the back of the tv. might be losing connection, can also be the the cable connection. so try using a different one, switch cleaner and the tv off at power before spraying the switch cleaner. also use an old tooth brush to remove any dirt. and spray again don't turn tv back on till it has dried. if after all this and its still the same this could be a problem with the connection to the board, and could need re soldering back on. or the controller chip for the av control has a problem, can be a build up of dust that has made its way into the chip joints, switch cleaner and brush should clen this out. dry joints on the board can also do this as when thy warm up they will disconnect and be no signal. while you have the back off the tv clean out the dust build up even on the back of the boards with an paint brush and a hoover. this will help the tv. clean out as much of the dust out as you can. but don't be to ******* the av board as this has small parts on this and if you knock a resistor etc off you will not be able to find were its from without a semantic. just spray switch cleaner and wipe around with the brush.

Element... • Answered on Mar 30, 2018


What code?

Element... • Answered on Mar 20, 2018


If its under a yr old return it as its in warranty

Element... • Answered on Mar 16, 2018


Test the remote using your cell phone camera, if it works then its in the inferred sensor board in the TV

Element... • Answered on Mar 11, 2018


You want the "A/V" input on the TV. Somewhere there's a 3-jack combination, two of which are red and white and the third is the video (yellow on the Xbox)

Element... • Answered on Mar 01, 2018


you can get a replacement like this that fit any tv. uses the wall bracket holes on the tv, replacement tv stands can cost a lot. this is the cheaper option and they look better and more stable. https://www.ebay.co.uk/i/222345567503?chn=ps&adgroupid=52137191441&rlsatarget=pla-380309527891&abcId=1129946&adtype=pla&merchantid=113584017&poi=&googleloc=9046240&device=c&campaignid=974961043&crdt=0

Element... • Answered on Feb 17, 2018


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main digital board.

Element... • Answered on Feb 17, 2018


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. https://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Element... • Answered on Feb 17, 2018


There is no such thing as a defuse board in a LCD TV, there are defuse screens in the panel is that what your talking about?

Element... • Answered on Feb 16, 2018


You are going to have to let us know which Element smart TV. Model number and such. You can go to... Support Element Electronics And enter the information on your TV. Down load the users manual which should explain how to do what you want. There is also a 'live chat' capability where they should be able to walk you through the process. Semper Fi, Z

Element... • Answered on Feb 13, 2018


Best way is via pc or laptop or smartphone which has tv or av output (some new sets have hdmi output that will work if your set has hdmi intput.

Element... • Answered on Feb 05, 2018


usually this is caused by a bad t-con board or a bad panel if its a panel your finished but if it is the t-con you need this part. see the link but I must warn you the part you need might not be available or may be different go inside your tv after unplugged and find the similar part and replace it elef328 con Google Search

Element... • Answered on Feb 02, 2018


Look for the part number on the board and order by that number not model number and you should be ok...what makes you think its the main, on that set power board issues were more common than the main board failing

Element... • Answered on Jan 31, 2018


Bad Tcon board

Element... • Answered on Jan 22, 2018

Not finding what you are looking for?
Element Logo

638 questions posted

Ask a Question

Usually answered in minutes!

Top Element Televison & Video Experts

Cindy Wells

Level 3 Expert

6259 Answers

The Knight
The Knight

Level 3 Expert

76584 Answers

ENFORCER

Level 3 Expert

38493 Answers

Are you an Element Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...