Element Televison & Video - Page 8 - Recent Questions, Troubleshooting & Support


Two things to check. The T- Con board and the back light strips. The T-con board can cause dimming on parts of the screen. A bad section of back light LEDS can do it also. Parts can be found here: TV Parts Universal TV Stands DLP Chips ShopJimmy

Element... • Answered on Apr 30, 2018


http://free.productmanualsfinder.com/index.jhtml?partner=^CON^xdm106&sub_id=1&s2=pmf_nc&s3=76c035&s4=1 Get your manual here.

Element... • Answered on Apr 30, 2018


http://free.productmanualsfinder.com/index.jhtml?partner=^CON^xdm106&sub_id=1&s2=pmf_nc&s3=76c035&s4=1 You can get your TV manual here.

Element... • Answered on Apr 30, 2018


http://free.productmanualsfinder.com/index.jhtml?partner=^CON^xdm106&sub_id=1&s2=pmf_nc&s3=76c035&s4=1 Go here to get your TV manual.

Element... • Answered on Apr 30, 2018


http://free.productmanualsfinder.com/index.jhtml?partner=^CON^xdm106&sub_id=1&s2=pmf_nc&s3=76c035&s4=1 Go here to download the manual for your TV

Element... • Answered on Apr 30, 2018


HDMI ports can die by getting a surge from a storm or power loss. You can get parts here: TV Parts Universal TV Stands DLP Chips ShopJimmy

Element... • Answered on Apr 30, 2018


The LED driver is probably on the Main board. There is the T-Con board too. To determine which parts you need, do this. With the TV on and listening to a program, shine a flashlight on the screen and look for a faint picture. If you see one, the LED driver is bad. If you don't see a picture, the T-Con board is bad. You can get parts here: TV Parts Universal TV Stands DLP Chips ShopJimmy

Element... • Answered on Apr 30, 2018


You can get an external stand that uses the VESA mount holes on the back of the TV. You can get them here: TV Parts Universal TV Stands DLP Chips ShopJimmy

Element... • Answered on Apr 30, 2018


Fine tune the position of the antenna. Sometimes it only takes a slight movement to capture those channels.If you don't have an amplified antenna, get one. That may solve your problem. The tuner will not manual tune if there isn't a strong enough signal for the tuner to see.

Element... • Answered on Apr 30, 2018


TV Parts Universal TV Stands DLP Chips ShopJimmy This place may have a remote for your TV. If not look at the Logitech Harmony remote control. That control is awesome.

Element... • Answered on Apr 30, 2018


Do the flashlight test. With the TV on and listening to a program, shine a flashlight on the screen. If you can see a faint picture, the LED driver is bad. If you cannot see a faint picture, the T-con board is bad. TV Parts Universal TV Stands DLP Chips ShopJimmy You can get parts here.

Element... • Answered on Apr 30, 2018


press source button a few times. or DTV on remote. or press menu and go to source and click on DVT or HDMI etc that you want the signal or have a signal from.

Element... • Answered on Apr 21, 2018


Ask for it to replaced or repaired under warranty.

Element... • Answered on Apr 20, 2018


Hello, Jose - Contact Direct TV Customer Service, Technical Support in the USA: 800-531-5000. You will need to have your account number and perhaps a PIN or other identification verification. Best wishes.

Element... • Answered on Apr 06, 2018


clean the jack on the back of the tv. might be losing connection, can also be the the cable connection. so try using a different one, switch cleaner and the tv off at power before spraying the switch cleaner. also use an old tooth brush to remove any dirt. and spray again don't turn tv back on till it has dried. if after all this and its still the same this could be a problem with the connection to the board, and could need re soldering back on. or the controller chip for the av control has a problem, can be a build up of dust that has made its way into the chip joints, switch cleaner and brush should clen this out. dry joints on the board can also do this as when thy warm up they will disconnect and be no signal. while you have the back off the tv clean out the dust build up even on the back of the boards with an paint brush and a hoover. this will help the tv. clean out as much of the dust out as you can. but don't be to ******* the av board as this has small parts on this and if you knock a resistor etc off you will not be able to find were its from without a semantic. just spray switch cleaner and wipe around with the brush.

Element... • Answered on Mar 30, 2018

Not finding what you are looking for?
Element Logo

637 questions posted

Ask a Question

Usually answered in minutes!

Top Element Televison & Video Experts

Cindy Wells

Level 3 Expert

6259 Answers

The Knight
The Knight

Level 3 Expert

76584 Answers

ENFORCER

Level 3 Expert

38519 Answers

Are you an Element Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...