Electrolux Washing Machines - Page 2 - Recent Questions, Troubleshooting & Support

0helpful
1answer

EWS1046 doesn't start, keeps clicking and returns E40 message when I try to launch a programm

the power surge might have ruined the relay or board
3/10/2022 7:05:15 PM • Electrolux... • Answered on Mar 10, 2022
0helpful
1answer

Electrolux w4180n error 36

google Electrolux w4180n error 36 for more info http://laundry.manualsonline.com/manuals/mfg/electrolux/w4180ns.html?p=109
3/9/2022 8:37:25 PM • Electrolux... • Answered on Mar 09, 2022
0helpful
1answer

Electrolux EWW1141AESA Washer-Dryer isn't drying

If it is new, contact the seller under warranty. This model is only available in Saudi Arabia, we are in North America. According to the specs, it is a condenser dryer with no vent to outside. These do take longer to dry, but they should dry eventually. https://www.electrolux.sa/en-sa/appliances/washer-dryers/eww1141aesa/#specifications ..
2/17/2022 8:34:02 PM • Electrolux... • Answered on Feb 17, 2022
0helpful
1answer

I have lost power to my electric oven, the breaker is good

Check you have power to the cooker before you try anything else.
2/6/2022 10:58:55 AM • Electrolux... • Answered on Feb 06, 2022
0helpful
1answer

Electrolux EWF1090. There is something between the drums in my washer.

Get a flashlight and put it against the holes in the inner drum and you will be able to see what the object is. If you pull the door gasket down and away, there is normally enough room to slip in a straightened wire coat hanger to hook it out.
1/28/2022 9:54:14 PM • Electrolux... • Answered on Jan 28, 2022
0helpful
1answer

Electrolux EIFLW55HIW0 Imperative to have exact original part# in drainpump replacement? Matched part#137408 put in not orig part (#137038700). Would inexact part# cause rinse/drain & other problems?

I would say you need the right part. Although they might look the same, the wiring to the pins might be different. Here is the part Fits your EIFLW55HIW0 Washer! Part Select Number PS2342436 Manufacturer Part Number 137038700 Manufactured by Frigidaire https://www.partselect.ca/PS2342436-Frigidaire-137038700-Drain-Pump-120V-60Hz.htm?SourceCode=20&SearchTerm=EIFLW55HIW0&ModelNum=EIFLW55HIW0&ModelID=1522373 I can't find the one they gave you. https://www.google.com/search?q=washing+machine+pump+%23137408 ..
1/26/2022 10:39:04 PM • Electrolux... • Answered on Jan 26, 2022
0helpful
1answer

Electrolux washing machine drum not turning. Door will not unlock.

The most likely cause is a broken drive belt. You don't say if it is a front or top loader. For a top loader, pull the machine out, and drop the drain hose into a bucket to empty the machine. Tilt the machine against the wall. Have someone steady it and look underneath. You should see the motor and belt, although some are direct drive. For a front loader, the belt is accessed from the rear of the machine.
12/22/2021 6:18:19 PM • Electrolux... • Answered on Dec 22, 2021
0helpful
1answer

My beep is sounding too low, I want it to be high same as before.

The sounder/speaker is part of the control board which cost nearly $300. How good are you with a soldering iron? Most people want to stop them beeping. https://www.youtube.com/watch?v=f05Y_rTQVg0 https://www.google.com/search?q=washing+machine+beeper ..
12/11/2021 11:56:40 PM • Electrolux... • Answered on Dec 11, 2021
0helpful
1answer

Pedestal door won't close electrolux pedestal #EPWD157STT

I am guessing it runs on rollers on a rail like a filing cabinet. See if it has dropped off. A quick search shows the normal issue is not staying shut. https://www.google.com/search?q=electrolux+pedestal+EPWD157STT+jammed ..
12/11/2021 1:12:58 AM • Electrolux... • Answered on Dec 11, 2021
0helpful
1answer

Electrolux Front load - the boot seal is wearing due to friction from the drum at approximately 2-3 and 9-10 o'clock. Is there a drum suspension component that is wearing out.

Yes, I would think you have a broken spring that is not holding the front of the drum up. Basically the drum should float flat and level with the springs and a gas strut or two.
12/4/2021 5:44:42 PM • Electrolux... • Answered on Dec 04, 2021
0helpful
1answer

Why does my Electrolux washer keep turning on and off by itself

Possible faulty control board. Leave unplugged until you need to use it or have it serviced.
10/21/2021 5:41:20 PM • Electrolux... • Answered on Oct 21, 2021
0helpful
1answer

How do I reset an Electrolux washer model EIFLS55IMB0

I haven't found your model. However the Electrolux EIFLW50LIW has a demo mode. The display will show Dn when in this mode. To toggle this off, first press the power button to turn off the washer. Then turn it back on. Wait for the console to light up and then at least 10 seconds more while it does the machine self-tests. Next press and hold Soil and Spin Speed simultaneously. Hold both for 5 seconds or until you hear a chime or the lights blink off then on again. The FAQ for the EIFLW50LIW gives pressing and holding Soil and Options. However, there isn't one specific Options button on the right of the console of the machine. Please note: if you hold these buttons too long, you could toggle a setting back on. The references I found: https://www.manualslib.com/manual/235416/Electrolux-Eifls55i.html?page=12#manual and https://na2.electroluxmedia.com/Original/Electrolux/Electrolux%20Assets/Document/Complete%20Owners%20Guide/English/137519000een.pdf . I hope this helps. Cindy Wells
9/20/2021 5:01:07 PM • Electrolux... • Answered on Sep 20, 2021
0helpful
1answer

Washing machine Electrolux EWF880

ttle way and see if the washing machine will start properly. Push start switch may need to be tested with a multi meter for continuity OHMS should show a closed circuit when pushed in or turned on. The start switch on some top load washers is often part of the timer and is activated by pulling out on the timer knob. Although not normally available as a separate part, the switch can be tested for continuity with a multi-meter. You will need to remove power from the appliance and then locate the correct timer contacts as noted on the wiring diagram. On some electronic controlled models, the start switch is a momentary contact type switch located on the control console. You can test this switch for continuity with a multi-meter when the push button is held in Overheating If you've run several loads, one after another, without any problem but suddenly find your washing machine refuses to start, overheating could be the cause. The simple way to discover whether this is the problem is to give the machine ample time to cool down, say for a couple of hours, and then try it again. If it works fine, overheating has been the problem and you may have a motor with bad windings. By the way my advice is free cuz God is good! All washing machines use a motor that is responsible for spinning and agitating during the cleaning cycle. Many top load brands use a reversing motor which means the motor spins in one direction for agitating and another for spinning and draining. If the motor does not start, but makes a humming or buzzing noise then it may be defective. To verify if the motor is at fault, remove the drive and /or pump belts and then try to start the motor again. On direct drive models, you will have to disengage the pump and the direct drive coupling to the transmission. If the motor starts, then the problem is with the transmission or the pump and can be further diagnosed by reconnecting each one individually. If the motor does not start or continues to hum or buzz, then it will need to be replaced Lastly CONTROL BOARD If the control board does not provide the proper voltage to the drive motor, fill valve, drain motor or door lock then the washer may not start. The main control board on most washers is complicated and difficult to diagnose without proper test equipment and procedures. You can visually inspect the control for signs of electrical arcing or burned or damaged components on the board. You should use caution when replacing a control board as sometimes the burned components are caused by external component failures.  HYPERLINK "https://www.repairclinic.com/RepairHelp/Washing-Machine-Repair-Help" https://www.repairclinic.com/RepairHelp/Washing-Machine-Repair-Help http://www.partselect.com/Repair/Washer/Will-Not-Start/ No wash agitation or spin? try these: WATER PRESSURE SWITCH: This switch keeps your washer from overflowing. It is responsible for shutting off the power to the fill valve and redirects the power to the timer to start the washing machine running once the correct water level has been reached. Meter check ur water pressure switch? You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube. If the machine starts to wash. the pressure switch is more than likely good ( No wash starts - then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED) another test u can do is Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. Or take the original hose tube and plug one end and blow into it AT the other end, it should be hard and have pressure, if it is easy to blow and u dont feel any pressure and it feels like the air is going out ? Sometimes they get busted open or a pin hole and release air causing the water switch diaphragm to not open. Another test u can make with a multi meter is by testing the prongs individually. # 15,16,17 (don't worry to much bout the numbers IF U GET THEM WRONG) place ur meter prongs on both out side prongs or connectors of the switch. (where the wire plugs into) take note of weather it shows OHMS or infinity ( open or close circuit) ? Now place the meter on the left outside and the middle prong, take note agin what it shows. Now place meter prong on the right outside and the middle prong. Agin take note what reading u get. ( you should actually get a reading of infinity in 1 and a reading of continuity or ohms in the other 2? Now the tricky part. Agin place a small tube or hose into the switch and blow into it, using the meter do the same test agin on all prongs. But now keep the pressure on the switch when u blow into it, in other words use ur tongue on one end of tube to not allow air to escape. When u test it agin now one of the prongs that once read infinity should now show continuity or ohms, and 1 of the other prongs that read ohms should now read infinity or open. . Motor Coupling If the washer won't spin or agitate the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. It is designed to fail if the washer is overloaded in order to protect both the motor and Drive Belt If the washer won't spin or agitate, check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't spin or agitate properly. mode shifter and or Drive Motor If the washer won't spin or agitate the drive motor might be defective. This is not common. Check all of the other related parts to this symptom before replacing the motor. If the motor is visibly burned out or physically damaged, replace it. Stator Assembly If the washer won't spin or agitate the stator assembly might be burned out. The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed. Transmission or clutch assembly not engaging due to going out or slipping. Door or Lid Latch Assembly If the washer won't spin or agitate the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design. Door Lock Motor and Switch Assembly If the washer won't spin or agitate the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design. Motor Control Board If the washer won't spin or agitate the motor control board might be defective. The motor control board provides power to the motor as well as direction and force. If the motor control board is defective the washer may not work at all or function properly. CHECK THE CAM DOGS INSIDE THE AGITATOR, AS THEY WILL HINDER THE AGITATION PROCESS. However in G.E models the cam dogs are replaced with what is called an agitator coupler. (located at bottom of tub) Remember to check the agitator spline as well for worn broken teeth. https://www.youtube.com/watch?v=LfWRyt1vj2w By the way my advice is free cuz God is good! water pressure-switch-location-undefined-undefined-0_3.jpg door switch jumper-undefined-undefined-1_2.jpg fuse gewasherfuselocation-undefined-undefined-4_1.jpg water press switch-undefined-undefined-9.jpg
8/20/2021 8:35:06 AM • Electrolux... • Answered on Aug 20, 2021
0helpful
1answer

My Electrolux washing machine working 21 minutes then pause

what cycle does it stop in?
8/17/2021 5:38:58 AM • Electrolux... • Answered on Aug 17, 2021
0helpful
1answer

Front loader. Why is there water in drum?

YOU MAY HAVE A BAD WATER INLET VALVE NOT CLOSING PROPERLY? Test the water pressure level switch a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub. On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level. If the tube has a leak, not enough pressure may be created to activate the switch and the washer may overfill. If the switch is defective it may also cause the machine to overfill. To determine if the switch is bad, you should first eliminate the air dome hose as a problem. Look for signs of cracks or worn areas on the hose. Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. If the air dome hose appears to be ok, then the water level switch may be defective. You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube. If the machine starts to wash. the pressure switch is more than likely good ( No wash- then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED). # Test procedures to follow when a GE Hotpoint washer is not filling * Disconnect the washer from the wall outlet * Set the timer dial on regular and pull the knob to turn the timer push-pull switch on * Set the temperature switch to the cold/cold setting * Open the controls panel to gain access to the water mixing valve solenoids * Touch the 2 terminals on the cold water solenoid with your volt meter test proves. Make sure that your body don't touch the washer cabinet, this eliminate the chance of getting an electrical shock. * Have someone plug the washer cord for you while you check the voltage * The reading should be 120 volts * Disconnect the washer from the wall outlet * Touch the 2 terminals on the hot water solenoid with your volt meter test proves. Remember, to keep your body from touching the washer cabinet to eliminate the chance of getting an electrical shock # 2 Have your helper plug in the washer cord again so you could check the voltage at the hot water solenoid The reading should be 120 volts. If you get 120 volts, this tells you that the wall outlet, the timer, the water temperature switch cold and hot water settings are working ok. 3 If the GE Hotpoint washer is not filling, the problem should be on the water valve, the screen filters or the water supply 4 If one of the solenoids is bad you will need to replace the complete water mixing valve assembly YOU SHOULD ALSO GET AN OHMS READING OR SHOW CONTINUITY WHEN TESTED UNPLUGGED ON BOTH SELINOIDS HOT AND COLD To check the water valve, first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed. If you still don't have good water pressure, the problem is in your house plumbing and you need to call a plumber. If you had good water pressure the first time you performed the test, the water valve is bad and needs replacing. inlet testing washerwater inlet valve-undefined-undefined-0_3.jpg inlet voltage test waterinlet valve-undefined-undefined-2.jpg water press switch-undefined-undefined-4.jpg
8/14/2021 12:10:12 PM • Electrolux... • Answered on Aug 14, 2021
0helpful
3answers

My Electrolux ewf1090 front loader door wont open

Turn the power off and leave for 5-10 minutes then turn on. This should release the door lock the problem could be the pump drain filter is blocked clean this and it should resolve future problems.
7/6/2021 12:18:17 AM • Electrolux... • Answered on Jul 06, 2021
0helpful
1answer

How do I get my Electrolux washer to wash with cold water?

Did you find out how? We have the older 7kg model, and the lowest temp setting I can find is 30 degrees. As we are off grid, and can't spare the power for the heater, I've had to disconnect the heater coil and connect the single water hose to the hot tap, hot water heated by gas. That means hot washes and rinses.
6/29/2021 12:39:51 AM • Electrolux... • Answered on Jun 29, 2021
0helpful
1answer
0helpful
1answer

Hi. I have a Electrolux EWF984 Washing Machine.

Mu machine looks like its only getting 10% of its power, the locking door lightvis bearely on, the LED lights on the front is just flashing every 15 secconds? Can anyone help solve the problem..
4/24/2021 8:33:38 AM • Electrolux... • Answered on Apr 24, 2021
Not finding what you are looking for?
Electrolux Logo

2,422 questions posted

Ask a Question

Usually answered in minutes!

Top Electrolux Washing Machines Experts

Brad Brown

Level 3 Expert

19163 Answers

David Shaub

Level 3 Expert

2994 Answers

Cindy Wells

Level 3 Expert

6551 Answers

Are you an Electrolux Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...