Dremel Tools & Hardware - Others - Recent Questions, Troubleshooting & Support


More supports, please refer to www.dieselgeneratortech.com

Dremel Variable... | Answered on Apr 11, 2020


There might be many reasons but the one of them is you might be obstructing its air intake passage and it is over-heating.

Dremel Tools &... | Answered on Apr 05, 2020


You can call Dremel direct at 1-800-437-3635 and order the part. Let me know if you need more information.

Dremel 395... | Answered on Feb 11, 2020


If the threads on the nut or shaft are stripped, the nut will turn freely and it can be removed with pliers by turning and pulling at the same time. If it won't turn, it is probably galled or cross-threaded. In that case, try penetrating oil first. If that doesn't loosen it, try heating the nut with a butane or mapp gas torch. Good luck.

Dremel Tools &... | Answered on Nov 13, 2019


your best bet will be ebay Then if that's not successful, check with these people
https://www.ereplacementparts.com/search_result.php?q=Charger%2C+dremel+1100
You'll need to know the voltage. The 100 volt charger is discontinued. They carry authentic Dremel parts.

Dremel Tools &... | Answered on Nov 02, 2019


You screw off the collar on the tool, remove the chuck and inner part. The chuck is replaced with a special chuck (no inner piece). The special chuck has a square opening in it's nose that accepts the square end of the flex shaft inner cable. Is is actually a speedometer drive cable, from yesteryear.
Then you pull the inner cable out slightly, if it will, and put the inner cable into the square opening of the special chuck on your dremel motor. once engauged, you carefully screw the outer shaft housing on to the end of your dremel motor.
What you want to avoid is damaging this area during flex shaft assembly. I have had success with turning the output side of the flex shaft, while tightening the outer flex shaft onto the dremel motor. Stop tightening if it starts binding...
Rotation seems to help with alignment of all parts.

Cheers,

Doc

Dremel Tools &... | Answered on Oct 02, 2019


Contact Dremel directly and inquire.

Dremel Tools &... | Answered on Oct 01, 2019


spray lube or oil and use pliers to move it back and forth

Dremel Tools &... | Answered on Jun 03, 2019


Just some observations:
- The correct blade has ti be installed.
- It has to be sharp
- It can only cut material intended for that blade.

Dremel 6300-05... | Answered on Jun 01, 2019


Change the capacitor 220uF and it will most certainly work again. I got the idea from FixYa and it solved my problem!
Easy to change just 2 soldering points and a component costing around 0,2 Euros. If you do not know how to operate a soldering tool ask someone for a quick assistance. The switch takes around 2 min (1,5 min to open the charger and 0,5 min to change the component!).

/Johan

Dremel & Stylus... | Answered on May 19, 2019


My stylus is doing exactly the same thing. l was advised by numerous people to change the capacitor in the charging dock, they also said that you can find youtube videos to guide you through it (the capacitor only cost a few cents when l bought it). I really should finish doing that job, although l did actually remove the 'screws'' from the base, l warn you- they are triangle and a nightmare to unscrew, see if you can find a triangle screwdriver BEFORE you start, or you'll end up doing what l did and destroying a perfectly good straight screwdriver!??. Good luck

Dremel & Stylus... | Answered on May 15, 2019


Fixya is unable to suggest sources for Dremel parts.

Dremel Tools &... | Answered on May 14, 2019


This is the charger, its getting a reading from the battery that its charged when it isn't. I don't know exactly how that charger is wired but, to be suroe it is the charger, as I have had similar problems beforehand.

Dremel & Stylus... | Answered on Mar 22, 2019


It's possible that the enameled copper coiling on the stator was compromised when it overheated creating a short. Sadly, unless you have a replacement stator is cannot be fixed. Sorry.

Dremel Tools &... | Answered on Feb 11, 2019

Not finding what you are looking for?
Dremel Logo

606 questions posted

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

cluffermon

Level 1 Expert

4 Answers

Mike

Level 3 Expert

4369 Answers

Van Allen II
Van Allen II

Level 2 Expert

277 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...