Dewalt Tools & Hardware - Others - Page 7 - Recent Questions, Troubleshooting & Support


What model gun is this? Framing, finish, battery powered?

Dewalt Tools &... | Answered on Mar 13, 2015


Power? circuit breaker? Plug? Owner's manual. Troubleshooting
Does the motor hum? if so you have something jamed in the planer cutter.

Dewalt Tools &... | Answered on Feb 28, 2015


dewalt nailgun jamming "constantly"

Dewalt DC618KA... | Answered on Feb 27, 2015


Brushes can definitely cause this but unless you feel fairly confident in pulling the unit apart, it may be more cost effective to just replace it. It would be unusual to see the brushes wear out so quickly but I do not know how much you use it or the load you put it under. I have a Rigid that I use a LOT and have had it for probably 5 - 6 years and it is holding strong. These things just tend to last. I would contact DeWalt and see if you can have them send you new brushes first and then go for it; the worst is that you ultimately have to replace it (which you might have had to anyway) and the upshot is that you fixed it yourself and now have many more years and sawdust sneezes in your future.

Dewalt Tools &... | Answered on Feb 14, 2015


is this a gas cartridge type of nailer? It could be the effects of gravity on the spray nozzle. try pushing down in normal position but dont fire it. quickly move to ceiling then try firing. I am not a fan of this type of nailer as they are problematic and finicky.

Dewalt Tools &... | Answered on Feb 11, 2015


I think you have to call the service center on this one,
http://www.dewalt.com/Find-Service-Center.aspx

Dewalt Tools &... | Answered on Feb 09, 2015


No - this nailer must be oiled (5-10 drops directly in air fitting before each use)

Dewalt D51256K... | Answered on Feb 07, 2015


A few things to check - some may seem overly obvious but humor me:
1) Check your nails - make sure they are the correct angle and gauge
2) Check to make sure there is not a piece of a broken nail in the nose
3) Check the driver blade & insure it is not bent or chipped
4) Make sure the nail carrier spring is pushing nails forward and isn't getting hung up

Dewalt DC628K... | Answered on Feb 07, 2015


Detail You can find the owners manual and parts breakdowns here

Dewalt 1 - 1/4 -... | Answered on Feb 07, 2015


5-10 drops directly in the air fitting before each use.

Dewalt Tools &... | Answered on Feb 07, 2015


Remove 2 screws on metal front cover.
Remove screws holding handle halves together and carefully separate (Be careful because trigger spring can fly out on you).
This will expose the belt and allow replacement. There is a spring loaded idler pulley so removal & replacing is easy.

Dewalt DC618KA... | Answered on Feb 07, 2015


That would usually be performed by a spring - is it OK?
25403509-453em5qn1uewfye2dfkecdof-4-0.jpg

Dewalt Heavy -... | Answered on Feb 06, 2015


I think that model is on a ring internally so there isnt a way to do like the bigger ones, you would have to take the screws out and take in half and you will the the brushes and can replace.

Dewalt Tools &... | Answered on Jan 12, 2015


you are going ot need to take it apart and see where it is corroded. there is most likely corrosion around the power supply to the laser itself.

Dewalt DW071KI... | Answered on Jan 09, 2015


The clutch is defective , you can get replacement parts from dewalt. There are several dewalt service centers in the US

Dewalt Tools &... | Answered on Jan 07, 2015


Use an Allen wrench to loosen the two or 4 bolts on nose of the gun. Take the plate off and remove offending nail.

Dewalt Round... | Answered on Jan 07, 2015


Did the light on the charger indicate that it was charging? (Most also have a "replace battery" or similar light.)

If so, and the drill keeps beeping...since it's new don't bother monkeying with it. Just take it back to the store and have them replace it. Dealing with a warranty repair will leave you without a tool for some length of time.

Dewalt DCF885C2... | Answered on Dec 31, 2014


To do the dew one must see the dew and then become the dew.

Dewalt Tools &... | Answered on Dec 30, 2014

Not finding what you are looking for?
Dewalt Logo

621 questions posted

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1420 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

john h

Level 3 Expert

23424 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...