Dewalt Tools & Hardware - Others - Page 5 - Recent Questions, Troubleshooting & Support


Go to this site and it will show you what you need to know. https://www.youtube.com/watch?v=PQ8lSB_mP1c

Dewalt DCF885... | Answered on Sep 13, 2016


Tap the end of the bit a couple of times with a light hammer. This will often shift it.

Dewalt DCF885C2... | Answered on Sep 12, 2016


Suggested the common Different materials for aal CAPEX or Marquard switches depends on build time and modification not to say for shure but together its like a great metal heatsink for heat dissipation for the mosfet phosphor-bronze contacts for L&R and the full high speed 1 only brass contact for regulate speed on the trigger that mount on a phenolic and or epoxyglas electronic print where the mosnfets and smd parts are on mounted and a black carbonfilm as a functional variable resistor for the rpm where the brass contact from the trigger make the speed sillicium parts and some solderings N076010 is for Type 1 the switch. the basic plastic material is unfortunately
not thermosetting material if there is bad connexxion by bad brushcontacts or sliding contacts priority on the left and right switch contacts they can melting down inside the switch and loose contact then the cause is overloading. it can be searched if the brown and purple wires the sliding contacts of them are weak and loose on the carbon brush holders. thats the first step to take action on your tool to repair
25963414-4lnkphpp13r3seubwfvzvuho-3-1.jpg

Dewalt 12 Volt... | Answered on Sep 08, 2016


If the tool asked more then thebattery can handle thearmatures and the batteries can became both in a to short time defect.

Panasonic EY7441 is a battery accuscrewdriver powertool that was delivered with 1.5 A batteries and 80% of all users have bad batteries and armatures in between 2 years of use, but the 3.3 A can have them over 3 years , but became later the problem but the batteries survived , but never the armatures. they began eating the carbon brushes in 3 weeks again and made a very shrill noise.

Dewalt Tools &... | Answered on Aug 05, 2016


Request the wiring diagram directly from Dewalt.

Dewalt DCF885C2... | Answered on Jul 19, 2016


The laser diode can be dead or one of the very thin wires on the laserdiodeunit can be broken

Because of the callibration of the laser and more small underlying defects in assembly and disassembly of the laser block and the x and y axis control is to abandon self-repair.

Dewalt DW071KI... | Answered on Jun 12, 2016


Time to replace a few orings in the trigger valve. There are at least three orings made of vinyl that fail, two on the trigger pin and one on the plunger.

Dewalt Tools &... | Answered on May 06, 2016


This problem is due to failed orings in the gun and the trigger valve. If you have access to orings, replace all the vinyl orings that feel sticky or like putty (at least 3 in the trigger valve). Finally, make sure that the driver blade moves freely within the cylinder and that there are no jammed nails within the path of the driver.

Dewalt D51256K... | Answered on May 05, 2016


The bulkhead on a nailer is the part that separates the pressure chamber from the lower compartment of the nailer. Usually round center hole for the cylinder to pass thru. The outer shape conforms to the inner contour of the body. Usually made of plastic some are metal and have orings seals or oring surface.

Dewalt Round... | Answered on May 05, 2016


Dewalt uses a combination buna and vinyl orings. The vinyl orings in their nailers fail by turning into putty. To fix your problem replace the trigger valve or the vinyl orings within. You will meed three orings in the trigger valve, (buna 70) , two rings are 2mm and one is 6mm. Within the body of the gun there are 5 more vinyl orings that fail. The rebuild kit has some vinyl orings and will most likely fail also. Convert to buna for longer life. Good luck

Dewalt Round... | Answered on May 05, 2016


What I do know is that some NiCd 12V Black decker batteries that look similar to the dewalt ones they are charged by the dewalt charger.
But there are 12V Nicd black and decker batteries that they can not be charged due to an extra plastic edge that does not allow to be charged by the dewalt charger.
Now if you do have the dewalt lithium 36V charger and if the black and decker battery is a 36V lithium one and can not be charged due to a plastic edge then I would recommend to risk to destroy the plastic edge in order the black and decker battery to be charged.

Dewalt Black &... | Answered on Apr 30, 2016


If it works when upright, perhaps the nose piece is not fully depressed. I have the same problem using my pneumatic finish gun.

Dewalt Tools &... | Answered on Apr 17, 2016


If the ball bearing of the armature was getting too hot by working with too hard woods may be the bearing of the armature can melting loss the drive belt have lost a little tension by it the housing and a bearing has to replaced in that case.

Dewalt DW680K... | Answered on Feb 26, 2016


You will either have to get a removal tool to take it out or drill/cut it out carefully.

Dewalt DW421 5''... | Answered on Feb 23, 2016

Not finding what you are looking for?
Dewalt Logo

621 questions posted

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1420 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

john h

Level 3 Expert

23401 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...