Denon Audio Players & Recorders - Popular Questions, Answers, Tips & Manuals


SAD TO SAY BUT UNLESS YOU HAVE TRAINING IN ELECTRONICS I DOUBT YOU CAN FIX IT

Denon Audio... | 25 views | 0 helpful votes


Power off using the power button and press together TUNER PRESET CH + and TUNER PRESET CH. Remove fingers when Initialized appears on the screen. It will reset the Denon AVR-X2300W.

Denon Audio... | 44 views | 0 helpful votes


I expect your tuner/amp has a fair number of ultra sensitive CMOS devices inside and a power surge is likely to be instant ***** for them - if the surge reached them.

Any piece of equipment that has a computer inside really should be protected by an anti-surge device.

Your Denon tuner/amp is a bit of really premium equipment and I advise you it is best to entrust it's resurrection to a Denon approved repairer.

Denon Audio... | 60 views | 0 helpful votes


if you want to set your playback speed exactly right, you need a test tape with a test tone on it (3khz for example). now you hook a frequency counter to your tapedecks output and set the speed accordingly.

Denon Audio... | 89 views | 0 helpful votes


Welcome to the most diverse technology & Telecommunication products provider in the US. We are the official partners of Plantronics, Logitech, Jabra, Gai-Tronics, Panasonic, Motorola, HIKVision, LOREX, RCI and UNIDEN technologies https://www.telegiants.com/

Denon Audio... | 96 views | 0 helpful votes


This will depend on the Blue ray player and other equipment. For a direct connection to the receiver, if your player has either type of digital audio output (coaxial or optical), get the appropriate cables. Then connect the chosen cable between the Blue ray player and the receiver. Connect the Blue ray player to the TV with an HDMI cable. See page 10 of the manual, available at http://pdfstream.manualsonline.com/6/69f43064-f593-49b8-8d4a-23174b496e65.pdf , to see the connections for the audio sources. (I'll assume your Blue ray player doesn't have component video out or you would use the component audio to the receiver.)

If your player doesn't have a digital audio output, check your TV audio output. You can get the same result by sending the videos via HDMI to the TV and using the TV audio out to the receiver. Set the audio source to TV and leave it there for both TV and Blue ray and DVD videos. (Sometimes there could be a slight delay in the audio compared with the video signal when you do this. I've never noticed it with my Blue ray player signal going to the TV and the TV digital audio out to the Denon receiver.)

If you can't send the audio out to the receiver from either your Blue ray player or TV, then you will need some sort of HDMI audio extractor. You can find models with Analog Audio Out, Digital Audio Out or both. ( https://www.amazon.com/J-Tech-Digital-Extractor-Converter-JTDAT5CH/dp/B00BIQER0E lists units with both types of audio output. One models requires a 3.5 mm to RCA audio adapter.)

I hope this helps.

Cindy Wells

Denon Audio... | 94 views | 0 helpful votes


https://searchmanuals.net/search94-sh/?keyword=%2Bdenon+%2Bmanuals&msclkid=7df6682623ae12d6f4d035cf55d9e058

Denon Audio... | 131 views | 0 helpful votes


set unit to phantom mode in the menu

Denon Avr789... | 76 views | 0 helpful votes


I find the best way to connect any equalizer is to connect via the tape monitor sockets, assuming that the AVR has one. From the equalizer in and out sockets - connect the Eq OUT to Tape IN on the AVR. And Eq IN to Tape OUT on the AVR.
Some AVR don't allow connections, due the equalizer interfering with Surround Sound systems. If you can connect switch off the equalizer when listening to Dolby or other surround formats, as it will spoil the sound.

Denon Audio... | 119 views | 0 helpful votes


Hi Ray Lynam, for what you say, you could have a problem with the speaker output
I suggest you remove the cover and look for two F2 and F3 fuses of 4Amp each that correspond to the output of the speakers, check if they are burned, if so replace them, ONLY FOR FUSES OF EQUAL VALUE 4AMP, do not put more value because you could produce major damage, test the equipment and if they burn again, then if you have problems at the exit stage
In this case, look for a specialized technical service
I hope you can solve the problem
Greetings Franco Dosil

Hola Ray Lynam, por lo que comentas, podr?as tener problema en la salida de parlantes
Te sugiero retirar la tapa y buscar dos fusibles F2 y F3 de 4 Amp cada uno que corresponden a la salida de parlantes, controla si est?n quemados, si es asi reemplazalos, SOLO POR FUSIBLES DE IGUAL VALOR 4 AMP, no pongas de mayor valor porque podr?as producir un da?o mayor, prueba el equipo y si se vuelven a quemar, entonces si tiene problemas en la etapa de salida
En este caso busca un servicio t?cnico especializado
Espero que puedas resolver el problema
Saludos Franco Dosil

https://www.hifiengine.com/manual_library/denon/dra-350.shtml

Denon Audio... | 38 views | 0 helpful votes


Try unplugging it. Another thing is some units have a fuse in the back. Check the fuse with a multimeter for continuity. If meter shows OL then replace the fuse.

Denon Audio... | 92 views | 0 helpful votes


(1)Download AVR3310 service manual.
(2)enter debug mode to see what kind of protect it belongs to.
(3)DC or ASO protect
(4)DC protect to check all smd transistors if leakage occurs or
differential and voltage amp transistors leakage
(5)ASO see service nanual troubleshooting steps.
(6)Replace all defective components.

Denon Audio... | 59 views | 0 helpful votes

Not finding what you are looking for?
Denon Logo

5,710 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5700 Answers

The Knight
The Knight

Level 3 Expert

76443 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...