Delta Plumbing - Page 8 - Answered Questions & Fixed Issues
We have a single lever
The cartridge should have pins that create proper alignment with the supply lines. New single handle faucets have limiters that allow you to control the amount of hot water. Check the limiter position. Its also possible that the cartridge is clogged with debris. Modern low flow plumbing appliances reduce flow by reducing the water passages inside the unit. Therefore they are more easily clogged.
1/30/2011 11:21:26 PM •
Delta Plumbing
•
Answered
on Jan 30, 2011
•
123 views
I have the model 470
Contact Delta at 800-345-3358 and ask for replacement parts. With the lifetime warranty Delta customer service was awesome and sent out parts I needed to fix this same faucet.
How do you take off
On some there's a ring that needs to be unscrewed. Others have a screw which holds them in place. The cause of the leak is a rubber O ring which needs to be replaced.
1/10/2011 12:19:45 PM •
Delta 2457...
•
Answered
on Jan 10, 2011
•
66 views
Can't keep single hole faucet
One method that I have had good results with is to shut off water supply to faucet and remove supply lines then remove faucet from sink. Clean surface of sink and faucet base and dry completely. Get a roll of double sided carpet tape andput a couple of layers on sink covering slightly larger area then faucet base.use rubber or plastic gasket that came with your faucet and put another ptece of tape on bottom side.Put your faucet back in and tighten retaining nut as tight as you can. You can trim excess tape from around faucet base with exacto or utility knife. Hope this helps you. Have a good new year and thank you.
1/2/2011 3:49:06 AM •
Delta Plumbing
•
Answered
on Jan 02, 2011
•
261 views
The hot and cold water flow from the faucet OK.
inside the centre spout of the faucet where it sits on the baseplate is a divertor valve. this is not functioning properly and should be replaced. check the delta web site for a break down of parts.
1/4/2011 1:29:04 PM •
Delta 2402...
•
Answered
on Jan 04, 2011
•
147 views
My delta signature faucet is
i am not sure which cap you refer to. there is a cap just below the handle. turn off the water supply for safety and remove handle then turn the cap counter clockwise. to replace the hose you should only have to disconnect at the handle to the sprayer and the other end at the faucet below the sink. if you wish to remove the faucet then after shutting off the water undo the nut below holding the faucet in place. delta have a good web site where you can see a breakdown of this faucet.
How do you remove a cap from a delta 522 faucet
Sorry to read about your problem, I hope this helps you out.
their is a round top part of the handle, take a knife and pry off the cap, then you will need a Phillips
screw driver
I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck
4 Thumbs - Very Helpful
3 Thumbs - Helpful
2 Thumbs - Somewhat Helpful
1 Thumb - Not Helpful
Replaced cold water bath stem
Sorry to read about your problem, I hope this helps you out.
sorry, improper install of that stem, try and re install
I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck
HOW DO I TAKE APART
Were you able to figure out how to take the Leland apart? I'm wondering the same thing, Thanks
12/13/2010 4:05:53 PM •
Delta Leland...
•
Answered
on Dec 13, 2010
•
322 views
Not finding what you are looking for?