Delta Plumbing - Page 6 - Answered Questions & Fixed Issues
Spout leaking on moen kitchen faucet
Remove the rubber O ring (turn off Water supply at meter first), then take your O ring to the hardware store to obtain a new one. You may have to stretch the new ring under hot wster before installation, If you do not feel comfortsble doing this yourself, call an expert.
1/16/2012 7:23:38 PM •
Delta Plumbing
•
Answered
on Jan 16, 2012
•
174 views
Tighten Delta kitchen faucet
If you have the two handled Delta, the cartridge itself can be replaced with a new one. The old one may have the O-ring seal deteriorating to allow it to move as you see it move. The O-ring itself can also be replaced by itself.If you have the single handle version and the seal the ball sits on is moving, the selas can be replaced, and they are simply fished out with a paperclip bent into a small L to hook the spring and seal and draw them out. If the single handle typ handle is loose it held in place by an "Allen wrench"/hex key wrench. If the handle is loose on a double handle type, just lift the "H" or "C" cap out of the handle and tighten with a phillips screwdriver. It might just be they never installed the screw.
1/16/2012 5:20:19 AM •
Delta Plumbing
•
Answered
on Jan 16, 2012
•
265 views
Delta 473 faucet very loose where it meets the granite
This is a view from the underside of our sink. Is this what you were talking about? The steel plate is W-shaped (upside down in this case) and has a single nut larger than 3/4". It's almost impossible to fit a wrench up there to tighten it.
In our Delta signature 470
The only way to stop the leak where you push the button is to replace the wand/head. Delta has a lifetime warranty on there faucets. Call Delta at 1-800-345-DELTA (3358). Give them your model # and they will send you the head for free.
Delta 2555-216 Victorian Double-Handle Centerset
If you notice right below the handle,there should be a small opening where ,by using an allen wrench you should be able to remove handle giving access to the stem retaining nut ......CAUTION... be sure cutoff valve is turned off(both hot and cold cutoffs.... under lavatory sink before removing..........unscrew retaining nut and remove stem.....hope that helps......
A leak at the base
Check the water connection to the wand to make sure it has a gasket in it .
Brand new delta roman tub
Cna you remove water line feeding hot side to make sure it has correct flow. It could have something blocking inside of water line. And check hot inlet side on faucet to make sure it is open and not blocked.
Remove line you can run water in a bucket to ensure that hot side water line has no blockage in it and have someone help you with turning water off and on for you.
8/2/2011 3:36:29 AM •
Delta Plumbing
•
Answered
on Aug 02, 2011
•
127 views
Delta single handle model 172
You need to contact Delta for the parts... which they will provide free of charge
This forum is just for advice not purchasing
I am repairing my Delta
Remove the set screw holding the handle on. Pull the handle off and then remove the large diameter slotted nut holding the ball valve in place. After you remove that the spout, remove the ball valve abd then just pull the spout up and off. You may have to work it back and forth and you may have to spray some WD40 and let it sit overnight. It will come off.
Pull down part stick so
Hi,
The spout can easily be replaced...
Check for a set screw underneath back at the wall...
If no set screw then simply twist the spout of by turning CCW...
Then find a replacement spout at your local HD, Lowes< or hardware and reinstall the new one...
The replacement spouts are so cheap that it is not worth trying to fix the old one..
heatman101
How remove plastic cap?
take the edge of a sharp knife and pry up on it,, use care not to damage the lip ,, I know its hard , But it can be done, if the lip does get a lil bent or scared, Use a nail sandpaper file to smooth the damaged edge
How do I remove the
at the bend in the faucet handle there is a hole that has a set screw in it
I have a delta Palos
The aerator simply unscrews by turning it counterclockwise. You may have to use a pair of adjustable pliers in order to remove the aerator. Wrap a rag around it to prevent scratching the aerator. There is no other filter in the unit but it may still be clogged if a large piece of debris enters the faucet. To dissemble the faucet, remove the set screw under the handle and pull the handle off. The set screw requires an allen wrench of the correct size. Now remove the cap and then with a large adjustable wrench remove the bonnet that holds the valve assembly in place by turning counterclockwise. Pull the valve assembly off and then pull the hub assembly off. Notice the o-rings and how they are installed. You now have the unit apart as much as possible. Clean it out and reassemble. This diagram will show you a breakdown of the parts and how they go together. Click the link for a larger photo.
http://www.deltafaucet.com/customersupport/documentation/467-DST.html?document=pd&documentIndex=0
5/3/2011 5:49:36 PM •
Delta Palo...
•
Answered
on May 03, 2011
•
413 views
Not finding what you are looking for?