Delta Plumbing - Page 4 - Recent Questions, Troubleshooting & Support

take the set screw out and repair the plastic washers inside it

http://www.faucetdepot.com/pdfs/473-DST_Parts_f575.pdf

Dry soap or goop stuck in the pump or line.

The diverter is supposed to leak a little bit, so it will disengage after you turn off the water. If the water is leaking out a little, that's normal. But if it is really leaking out you may need to replace the entire spout.

Check installation manual if there is some indication about some kind of advice for this case. If there is no indication for the user, most probably your Delta Touch20 kitchen faucet is defective. Check your warranty terms about how you can return it to be changed or send it for service, so probably you'll have to uninstall it.

Just received the new part for the domo. My model is older and is chrome with black. I have removed the top screw and need to know what is the next step in taking apart the rest of the faucet so I can replace the new part # k.32.60.00

Thank you, Stuart

Here's a link to some info on restringing blinds which you'll have to do if you replace the blinds. For the trouble I would just get new blinds. Working with blinds can be frustrating even after you've done it a few times. On the other hand, it's fun to learn a new skill. Good luck!

http://www.howtomendit.com/answers.php?id=81955

There is a set screw under a removable button cover on the handle. Remove screw to disassemble and access cartridge. See link. http://www.deltafaucet.com/media/MandI/76075%20Rev%20B.pdf

The rubber gasket needs to be replaced...

IF YOU REPLACED ALL NEW PARTS THEN I WOULD GUESS THAT IT IS NOT PUT BACK TOGETHER RIGHT SOME THING MAY BE JUST A BIT OUT OF PLACE INSIDE CAUSING IT NOT TO SEAL. TAKE APART AND PUT TOGETHER AGAIN MAKING CERTAIN THAT EVERY THING IS LINED UP RIGHT. IF STILL LEAKS I'D GET A NEW ONE.

THERE HAS TO BE SOME THING HOLDING IT ON IT WILL NOT STAY BY ITSELF LOOK FOR A SMALL BOLT YOU CAN UNSCREW TO TAKE IT OFF. USE SOME WD 40 OR RUST REMOVLS SPRAY TO HELP LOOSEN.

THERE IS A BALL JOINT INSIDE THE FAUCET THAT YOU WILL NEED TO REPLACE YOU CAN GET A REPLACEMENT FOR IT AT LOWE'S OR HOME DEPO AROUND 5 BUCKS.

THE LINE MAY BE CRIPPED. TIGHTEN THE NUT OR REPLACE THE NUT IF IT WILL NOT TIGHTEN. YOU MAY NEED A LONGER WATER LINE TO GET AROUND THE BUMP.

LOOK FOR A SET BOLT UNDER THE SPRAYER TAKE IT OUT TAKE SPRAYER OFF TO REPLACE

TAKE IT APART. LOOK FOR SMALL SET (ALLEN) NUT/BOLT OR REGULAR NUT/BOLT YOU CAN TAKE OFF THEN TAKE OFF HANDLE AND REPLACE THE O RING.

LOOK UP ON LINE UNDER 3S10H/C VALUE KIT FOR BATH TUB FAUCET. SEE IF THERE IS A MANUAL OR A TROUBLE SHOOTING PAGE.

IF CROSS THREADED YOU MAY HAVE TO USE TWO PIPE WRENCHES ONE TO HOLD FAUCET IN PLACE THE OTHER TO TRY TO UNSCREW IT MAYBE YOU COULD USE SOME WD40 OR SOME RUST REMOVEL SPAY TO GET IT LOOSE IF IT IS SO TIGHT THAT IT JUST WILL NOT BUDGE YOU MAY HAVE TO CUT IT AND BUY A WHOLE NEW FAUCET.

Hi, there is two possible problems, first off could be the tap jumper or there is air trapped in the pipes. Try replacing the tap jumper, alternatively open all the taps to release the air

DID U TRY LOWS OR HOME DEPOE. OR TRY Rubber Delta Faucet‎

If the copper pipe is indeed leaking, you'll probably need to open the wall to fix it. Sometimes you can open the wall in back of the tile, in the adjoining room. Make sure this is the issue before you start this process.