Dacor Ovens - Answered Questions & Fixed Issues


Usually when an oven is slow to heat, it is because of a bad element. You can look at the upper (broil) and lower(bake) and see if they appear to have any major burn marks on them, It may just look like something spilled on it untill you look closer or try to clean it off. if you do not find any obvious problems, turn the oven on and wait a fem minutes, then see if the bake element is glowing. Also look at the broil element, they should both be glowing at least a little orange. Compare how it works to the other oven that works properly. If only one of your elements is glowing, either you have a bad element (which is usually apparent on visual inspection) or a bad relay board that controls the element. The element is easy to change, onlt a couple screws and 2 wires (turn off the breaker first!!), the relay board is pricey, and a pain in the tookas. if you decide to guess, try the element first. Hope this is at least a little helpful.

Dacor ECD227... | Answered on Mar 24, 2020 | 808 views


FixYourBoard.com will test and remanufacture the relay oven control board in this model. Each rebuild comes with a two year warranty.
Reach out to us at 512-355-1108 or [email protected]


fixyourboard 101559 repair-undefined-undefined-0_8.jpg

Dacor MCS130... | Answered on Mar 24, 2020 | 414 views


The code is telling you that the oven has sensed a fault in the coling fan circuit of the upper oven. Dacor has had a few problems with the cooling fans in these new ovens since theyve been out, so most likely you will have a bad fan motor. If that is the case, be prepared to have the repair person have to pull the oven out of the wall to get to it and change it. If its a realy board problem (less likely) than that can be changed from the front. Call up Dacor and find an authorized servicer in your area since it will still be under warranty. Good Luck!

Dacor Millennia... | Answered on Mar 24, 2020 | 1,393 views


FixYourBoard.com will test and remanufacture the relay oven control board in this model. Each rebuild comes with a two year warranty.
Reach out to us at 512-355-1108 or [email protected]



fixyourboard 101559 repair-undefined-undefined-0_6.jpg

Dacor Ovens | Answered on Mar 24, 2020 | 753 views


FixYourBoard.com will test and remanufacture the relay oven control board in this model. Each rebuild comes with a two year warranty.
Reach out to us at 512-355-1108 or [email protected]
fixyourboard 101559 repair-undefined-undefined-0_4.jpg

Dacor Epicure... | Answered on Mar 20, 2020 | 302 views


FixYourBoard.com will test and remanufacture the relay oven control board in this model. Each rebuild comes with a two year warranty.
Reach out to us at 512-355-1108 or [email protected]
fixyourboard 101559 repair-undefined-undefined-0_2.jpg

Dacor Ovens | Answered on Mar 20, 2020 | 868 views


FixYourBoard.com will test and remanufacture your faulty oven control board. Each rebuild comes with a two year warranty.
Reach out to us at 512-355-1108 or [email protected]
fixyourboard 101559 repair-undefined-undefined-0_1.jpg

Dacor Epicure... | Answered on Mar 20, 2020 | 389 views


were the both the same voltage and don't touch the bulb with your fingers us clean rubber gloves

Dacor Ovens | Answered on Feb 02, 2019 | 54 views


Step 1 Locate the "Clock" button on the display. The display is located above the oven door. It clearly shows the time and has settings for temperature, time and cooking.
Step 2 Press and hold the "Clock" button until the time starts to blink.
Step 3 Set the time with the number pad. Ignore the colons and enter the number straight through. For example, if the current time is 10:08, just type 1-0-0-8.
Step 4 Set AM and PM by pressing the "#" button. Press "Start" to finish.

Dacor Ovens | Answered on Jul 07, 2018 | 106 views


Page 9-48 in technical manual excerpts at the link below:

http://www.uncleharrywizard.com/nephewclub/WizardRange/dacor/dacor-wall-oven.pdf


http://www.uncleharrywizard.com/nephewclub/WizardRange/dacor/dacor-wall-oven.pdf


It says to call for service (by a technician). (I am only reading it from the document - I am not a technician.)

It says to replace glass/touchpad assembly.
It says wrong or unrecognized diode configuration.

Dacor Ovens | Answered on Apr 03, 2018 | 1,250 views


THIS SOLUTION FOR THE U6O ERROR CODE ALSO WORKS FOR OTHER ERROR CODES. I USED IT FOR THE L60 ERROR AND IT WORKED LIKE A CHANP. THANKS

Dacor ECD230... | Answered on Jan 19, 2018 | 1,047 views


quite possibly the element burnt out .

Dacor MCS230SS... | Answered on Sep 22, 2017 | 91 views


Still active problem?

Dacor ECS230... | Answered on Jul 26, 2017 | 904 views


Still active problem?

Dacor Ovens | Answered on Jul 26, 2017 | 174 views

Not finding what you are looking for?
Dacor Logo

Ask a Question

Usually answered in minutes!

Top Dacor Ovens Experts

Tyler T

Level 1 Expert

35 Answers

Lollo Pop

Level 2 Expert

134 Answers

Vincent G
Vincent G

Level 3 Expert

2363 Answers

Are you a Dacor Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...