Go to Control Panel >> Sounds and Audio Devices. Click on Advanced button under Speaker Settings and for Speaker Setup select 5.1 surround sound speakers from the options. Click Apply >> Ok and then check.
I Think its a loose connection in electric circuit. Due to vibration in the woofer the connection might be going off. Check the power circuit for any loose connections.
posted by Sandeep Sharma hai, Here is the solution. when u cut the PCB from both sides u will
find 4 cables i.e. green blue yellow and a copper wire coming from
woofer and 3 cables white, red, yellow coming from audio lead. connect
the green cable to copper cable and yellow to blue coming from woofer.
Now take white cable coming from audio jack.connect this with yellow
blue cables of woofer. Now attach Red and Yellow, connect these to
green and copper cables of woofer and enjoy. if problem persist then
make experiment to make interchanges with red white yellow coming from
audio lead to the 2 sections of woofer side. woofer connections
green/copper and yellow/blue remain same.
posted by Sandeep Sharma
[email protected]
The previous poster is right; I do repairs on these all the time, and the most common problem is a cracked screen. The crack is on the back so you can't see it. The screen will need to be replaced.
The volume control is nothing more than small complicated rheostat. If you don't know electronics take it to a radio repair shop. Just tell the repair guy to build you a new one using the old cord. That is if the cord is not what is bad! Take the entire unit with you. For a trained repair man it should be a easy thing to rebuild. I own a P7800 and if the control unit should break that is just what I would do.
I had the same problem: "Playback error", and nothing i did, helped. But when i pushed the reset buttom, below the on/of button, it turned of, and when i switched it on again, it worked. Maybe you could try again?
Otherwise I say this on YouTube, but thought it was a little drastic ;-)" />
I had an extra one but I sold it. According to creative labs they do not sell any replacement parts for the speaker systems. The best suggestion that I can give is to check craigslist and ebay for the control pods.
Stupid question: does the sound still work? it could be the LED just died after continual use (rare, since they last a long time, but not uncommon). If not... it could be the controlling circuit board died. In which case, unless you have electronics repair experience, it would be probably more worthwhile to just replace the speakers, as pricey a model as it is.
uninstall and reinstall the sound driver and see if it works if that does not work try the same speakers to different sys. and check if it works the port of the sound card might have gone bad and if the same problem with other sys. speakers had gone bad.
remove the device then runn the program and when it asks you to connect the device then connect it if that doesnt work please post an aditional comment and i'll see if i can help you out more :)
I used MediaMonkey I have successfully encoded over 1000 mp3 with the album artwork interlaced in the ID3 tag. The only issue I have now is that some of the artwork shows up and some doesn't? If I open the same music in a media player that supports album artwork it shows up fine?
Hello
You can find any type of controllers online anywhere
ebay/Amazon
or according to me Aliexpress Homepage
It's the biggest and cheapest worldwide suplier.
Just type the correct name into the searchbox and
thats it
Enjoy
If you check the Creative forums there is a thread there where a few people have started to fix problems like this permanently and they have helped quite a few people fix their problems. I would only suggest checking it out if you have any electronics experience (soldering, and basic troubleshooting minimum). Otherwise I would send it back but keep in mind that this is one of a few common problems with the S750's and you are likely to have other problems in the future unless you take measures to fix the problem that creative has not.
I would also like to point out that your problem would be a short on one of the amp boards after the power regulators, very likely one of the STA575 amplifier ICs. Those are not easy to find but it is possible to find replacements.
you won't be able to sync the avi file because your type of avi is not supported in the Zen
if you have the creative software on your computer well go
into the menu and select creative, because I don't have it in front of me I can't tell you where this is though all you have to do is search through and look to find "video converter" it's as easy as that.
all you do is when you find this is browse for you file and say what format you want to format to and start formating. they will ask if you want to sync you finished file to your zen.
