Citizen Skyhawk - Recent Questions, Troubleshooting & Support - Page 6

Set watch to CHR mode, pull out crown, all dials will return to 0 posn. HR shoul be displayed on left digital panel. Move hour hand by turning crown to posn half way between 12 and one, press top button (MIN should appear in left panel), set min to 6 o'clock posn. Push crown back in and set time for timezone nearest to where you are that is offset by one hour.

You probably need a new capacitor in the watch it, sounds like there is a malfunction. Eco drives should only go to Citizen for repair you can sent it in yourself and save ALOT of money!!

An Eco drive citizen is powered by the sun. You should take the watch out in the sunlight or put under a lamp to charge it for at least 12 hours. Once it is running you need to wear it to keep it running, you should be able to take it off at night and it will continue to run once it is fully charged. if it does not hold a charge over night after being fully exposed to light for 24-48 hours you may need to send it to Citizen for service on the capacitor. thank you!

Hi!

The problem you described is caused by incorrect setting of the hour: AM and PM must be set correctly, AM before noon and PM afternoon.

For more details regarding setting of your watch, please visit Citizen site here:
http://www.citizenwatch.com/COA/English/settings.asp

Please let me know if it helped,

good luck!

an Eco-drive does not have a battery, it has a rechargeable power cell that is charged by light through the face of the watch. If you have replaced this cell you may have damaged the watch. If the cell was not soldered in, replace it and put it under a fluorescent light for a little while (several hours) and it should start working.

http://www.citizenwatch.com/COA/English/faqs.asp?topic=Eco-Drive

http://www.citizenwatch.com/COA/English/rechargeguide.asp

http://en.wikipedia.org/wiki/Eco-Drive

The answer just depends on your preference: you can use a glass to glass adhesive and it should hold up fine. Just make sure that when you are attaching the crystal it is in the exact spot you need it to be in and also to have a small clamp ready to press over it. This will help to seal it better and make it last longer. If you don't feel up to it, I would take it by and let a jeweler take a look at it. Either way it's going to be a small fix. Hope this helps!
FlamePants

You can look up the setting instructions for your watch here:
http://www.citizenwatch.com/COA/English/settings.asp

Here is the manual for your Eco-Drive JR3000-51F:
http://www.fixya.com/support/p140220-citizen_skyhawk_eco_drive_jr3000_51f/manual-1591# I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Hi Hennie. Je moet de zomertijd op automatisch zetten. Ga naar http://www.citizenwatch.com/COA/English/settings_int.asp?caliber=U600&interactive=U600
Groeten, Jaap

you need to unscrew the crown first then you can pull it out to adjust the time
,,,,,,,,,,,,,,,,,,,,,,
For all those who lost their Citizen watch instructions. Follow this link, fill in the details and download manual. http://www.citizenwatch.com/COA/English/settings.asp Interactive setting instructions on this site is very helpful as well

The watch probably needs re-charging.

Go to http://www.citizenwatch.com/CUK/English/rechargeguide.asp, fill in the details of your watch and read the instructions.

Pull out the side round piece. Then turn it backwards. This should work. It might be two notches out, instead of pulling it out once.

You can get instructions from the Citizen web site.

Go to "citizen.com" and on the upper right there is a menu. Click on "technical
support" and then on "setting instructions"

Fill in the information required from the back of your watch and then click on
"get setting instructions"