Citizen Office Equipment & Supplies - Recent Questions, Troubleshooting & Support
My citizen cbm-910 11 will not power up
MOVED YOU OUT OF CARS/TRUCK
TO COMPUTERS + PRINTERS.
TYPE II, NOT 11.
NO FULL MODEL TOLD THE END OF MODEL SHOWS VOLT\AGE(PACK)
100 OR 120 OR 230VAC
IF USING PRINTER IN WRONG COUNTRY THE FUSES IN THE PRINTER BLOW UP.(page 13 in your free manual on line) OR THIS CASE THE POWER PACK.
FAILS DIRECT TO A WALL JACK KNOWN GOOD.
OR TO OLD POWER STRIP THAT LOVE TO FAIL (JUNK QUALITY MOST)
THIS PRINTER USES
A DC POWER PACK
USING THE WRONG PACK YOU ARE.
WRONG AC SIDE VOLTAGE OR OUTPUT SIDE DC WRONG
OR DC END WRONG POLARITY OR NOT AT LEAST 1.6AMP RATED
I MAKE ALL MINE WITH A TAG (FOR CBM910) OR I FAIL HARD.
HAVE LIKE 20 WALL WARTS HERE. ALL MARKED.
THE POWER PACK(WART) MUST BE
DC 7 V ±1 V (Printing)
Use exclusive adapter (DC 7 V 1.6 A)
AC SIDE MATCH TO COUNTRY AC VOLTS
AND THE DC JACK THE PLUS PIN MUST BE RIGHT
IT'S ALL HERE BUT THEY ASSUME PACKS NOT LOST OR MIXED UP WRONG
https://www.manualslib.com/manual/28188/Citizen-Cbm-910-Type-Ii.html?page=14&term=DC&selected=1#manual
The printer is not printing receipts and the error
Flashing (approx. once every second): Out of paper
Flashing (approx. twice every second): Mechanical error (Buzzer sounds once.)
Most likely your paper feed is giving you the error. Remove the current feed, ensure there are no paper jam & insert fresh paper.
If
Mechanical Error :: Quick blinking Buzzer Sounds continuously for a pprox. 1 second :: Reset the Power
switch
Paper End Blinks.:: Buzzer Repeats a short 3-time sound twice at intervals of 0.5 second.:: Set a new paper roll.
Paper Near End Blinks.(Once a second) :: buzzer Repeats a short 3-time sound twice at intervals of 0.5 second.:: Set a new paper roll.
Mechanical Error : If the printer mechanism has a greater load due to a paper jam, etc., the buzzer will sound and the SEL/ERROR lamp will blink to stop the printer mechanism.
Paper End : If the printer has run out of paper, the paper sensor in the paper path near the print head will detect the end of the paper roll, turn on the buzzer, and blink the SEL/ERROR lamp to stop the printer mechanism. If the paper is inserted into the paper path, the paper will be loaded.
Paper Near End : If the paper is running out, the paper near end sensor will be activated to turn on
the buzzer and make the SEL/ERROR lamp blink. Even after the paper near end is detected, a command can be used to print by the specified number of lines. (See a description on the command for setting the number of print lines after paper near end detection)
Finally
Backup Data Clear : When the power is turned on, depending on the SEL switch operation, the
backup data in the input buffer will be cleared according to the flowchart on the next page.
To clear the input buffer, turn on the power while pressing the SEL switch.
The following messages will be printed.
"Clear Data in Buffer"
"Cleared Data in Buffer"
To print the data in the input buffer, simply turn the power on.
The following message is printed and the data in the input buffer is printed.
"Power Down(Data in Buffer)
Printer is in an error state
You are a printer user, you have possibly faced a Printer is in an Error State problem. If you come across one, an error note will pop up on your PC telling you Printer is in an Error State. Your printer cannot get to run at this time. If you want to find some helpful answers to this problem. You can give the methods below a try. This blog can help you to fix your Printer is in an Error State issue.
Easy steps to solve Printer Is In An Error State:
1. Check the attachment and Reboot your devices.
2. Update or reinstall the printer driver.
3. Contact printer Service Provider.
4. Full BLOG with SOLUTION-
Printer Is In An Error State
The Printer Is In An Error State difficulty while trying to get a print from your printer on Windows? A Printer is in an Error State is a simple problem that is faced by all brands of printers. If you have updated your system from a previous version to the latest Windows, you might be facing this problem a lot more. In this step-by-step tutorial, you will learn how to fix the Printer is in an Error State.
If the Printer Is In An Error State is not resolved, this might mean there's waste within the printer's inside. Check this Blog for a full solution or Call customer services.
My sharp el-531x shows alot of zeros
Go to SETUP, press 0. The display will say “fix” “sci” and “eng”. Press the up arrow. Click the number four for Norm 2. Only one zero will show.
ERROR LIGHTS
Go to this site for help on light/beep codes.
http://www.goodson.com.au/download/manual/cbm/user/CBM1000II%20User%20Manual.pdf
Can't raise flame level
Obviously, if you read my post, I DIDN'T solve the problem because the problem WASN'T with a PRINTER but with a HEATER. I know that there are Dearborn heaters all over the place, but for some reason your site doesn't want to address them.
11/8/2018 5:30:46 AM •
Citizen...
•
Answered
on Nov 08, 2018
Citizen 3540
Get your converters on ebay. If you go to any electronic, computer store you will get hosed.
Not finding what you are looking for?