Chrysler Car Audio & Video - Page 3 - Recent Questions, Troubleshooting & Support

Unfortunately, these Chrysler codes are not available anywhere on the Net for free. However, you can get these codes from the serial number here. I have always found them cheap and reliable.

They will email the code right back to you on the same day and I can vouch for them as I use this site for Chrysler units I repair that occassionally need a code.

Hope this is of some help. Many thanks for using FixYa.

Unfortunately, these Chrysler codes are not available anywhere on the Net for free. However, you can get these codes from the serial number here. I have always found them cheap and reliable.

They will email the code right back to you on the same day and I can vouch for them as I use this site for Chrysler units I repair that occassionally need a code.

Hope this is of some help. Thanks for using FixYa.

Need to check the power to the radio to confirm if this is power related. if not does the display come on without sound which can be a faulty speaker or power amplifier within the unit.
finally if there is request for codes if the battery was reset then the specified code must be put into the radio to make it work.
check this link for codes.

http://www.radio-code.com/ http://www.floodle.net/extra/ebayinfo/car_radio_decode.html

Aux input is an input for you to plug in any auxiliary equipment such as an ipod or mp3 player etc.

CLICK HERE for Chrysler Code

Post the PART NUMBER beginning with P++++++++++ and the SERIAL NUMBER beginning with T+++++++++++++

Not having tried this on your make but normally you have to leave the ignition ON for 30-60 minutes without turning it off (Or the timer starts again). I have done this many times and think that this will be the correct solution. Please let me know?
Good luck with it.

With some new cars they have an amplifier for your speakers. You might have blown a fues to this amp. This amplifier should be in the trunk. But the fues might be with all the other fueses.

You are using the wrong code.

CHRYSLER codes are available here

CLICK HERE

Yes, you can get your Chrysler radio code here

CHRYSLER CAR RADIO CODE UNLOCK DECODE BY SERIAL NUMBER

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270684898336&ssPageName=STRK:MESELX:IT

CHRYSLER CAR RADIO CODE UNLOCK DECODE BY SERIAL NUMBER

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270684898336&ssPageName=STRK:MESELX:IT

Providing you have the correct code, the numbers are entered directly by pressing the corresponding buttons on the front of the radio...and when the last button is pressed then the radio should then work.

There is no further button required to be pressed to enter the code.

Get your Chrysler code checked CLICK HERE

Let me have the PART NUMBER beginning with P++++++++++ and also the SERIAL NUMBER beginning with T+++++++++++++

These are both found on a label on the radio casing

call a dodge or chysler dealer and get a find out who repairs there radio and send out for repair sounds like a bad radio or maybe a recall on the type of chysler factory radio ..simple solution is check craigslist for a working cheap aftermarket radio .then go out buy a dash kit, wire harness and antenna adapter and then install new used radio that is the cheapest solution.

http://www.google.com/imgres?imgurl=http://images.wrenchead.com/smartpages/partinfo_resize/GAT/S6003.jpg%3Fwidth%3D300%26height%3D300&imgrefurl=http://www.chevroletforum.com/forum/showthread.php%3Ft%3D33530&h=300&w=400&sz=22&tbnid=x499FyMjvH8kxM:&tbnh=93&tbnw=124&prev=/images%3Fq%3D96%2Bchevy%2Bcorsica%2Bbelt%2Bdiagram&usg=__jV5JG7XxMOdxq9p8AHZesz21dBM=&sa=X&ei=5rZmTM6pA5Kgngf1sdS4CQ&ved=0CCkQ9QEwBg

The only place I know apart from the Main Chrysler Dealer is by emailing here

[email protected]

Mention this forum

put in a after market radio like Kenwood, Sony or Pioneer

Please look in the fuse box in the car on the driver side of the daskboard.

Good luck.