Chevrolet Logo

Chevrolet Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 2K Products
  • 580K Answers
  • 8M Views

right behind the gear shift is the arm rest...it should open up...look and for screws and remove...then look around the front and check for screws there too...then pull up on console and around the shifter assembly you should see a light bulb and replace it...

2004 Chevrolet... | Answered on Feb 10, 2020


Where is the theft deterrent at in a 06 equinox

2005 Chevrolet... | Answered on Feb 09, 2020


Check the instrument panel fuse box. Your looking for a fuse called "APO JACK"

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

2010 Chevrolet... | Answered on Feb 07, 2020


https://www.youtube.com/watch?v=ItblmvAz6Wk

Chevrolet S 10... | Answered on Feb 06, 2020


EGR valves work in an ugly environment. When they fail it is almost always a replace situation, as the exhaust damages the internal parts.
IF your code says problems with the EGR valve, consider replacing it.

Chevrolet Cars &... | Answered on Feb 05, 2020


I found this info. Note, these databases are not always correct, but, it's all I have.
11619153-rg1ef4lamymlkzrkneh4f044-4-0.jpg

11619153-rg1ef4lamymlkzrkneh4f044-4-2.jpg

Chevrolet Spark... | Answered on Feb 04, 2020


Have the vehicle scanned for codes.If you have codes p0010,p0011,p0013,or p0014.You need to replace the intake and exhaust actuators.They are on top off the engine next to number 1 cylinder.And then have your oil changed.

Chevrolet Cars &... | Answered on Feb 02, 2020


according to lubeguard it is the answer to all of your transmission problems
basically it will not make much difference to the transmission but it may improve the performance if you use it as an oil change
From experience items sold are subject to user results and some say it is wonderful and others will say that it is not worth the money
use it and if you are not happy with the results you can always change it out for another oil

2000 Chevrolet... | Answered on Jan 31, 2020


DTC P025A: Fuel Pump Flow Control Module Enable Circuit
The engine control module (ECM) supplies voltage to the fuel pump flow control module (FPCM) when the ECM detects that the ignition is on. The voltage from the ECM to the FPCM remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received, the FPCM closes the ground switch of the fuel pump and also supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.
Circuit/System Testing
  1. Ignition OFF, disconnect the harness connector at the FPCM.
  2. Ignition OFF, install a test lamp between the control circuit terminal 13 and ground.
  3. Ignition ON, verify that a test lamp illuminates for 2 seconds.
  4. ?‡'
    If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

  5. If all circuits test normal, replace the FPCM.
Relay for what ? Which engine do you have LY6 or non LY6

2009 Chevrolet... | Answered on Jan 29, 2020


If you have someone scan the computer for trouble codes, the code will point you in the right direction to find the problem.

Chevrolet Malibu... | Answered on Jan 27, 2020


Try a sealant . It worked for me

1999 Chevrolet... | Answered on Jan 26, 2020


there is no fuel pump cut off switch on this car, it is possible the fuel pump module was damaged from this accident, u will have to have the fuel pump circuit tested for faults before replacing the pump, don't guess, this is an expensive repair

2003 Chevrolet... | Answered on Jan 22, 2020


did you check you fuel filter and your fuel pump? i had the same problem and once i replaced the fuel filter its been fine since

1997 Chevrolet... | Answered on Jan 22, 2020


DID YOU FIX THIS ISSUE ALREADY.. IM HAVING THE SAME PROBLEM..PLEASE ADVISE.

THANKS

2012 Chevrolet... | Answered on Jan 21, 2020


Hello,
It depends on your ac fan, you will be not able to clean the fan without a tool because to remove the fan you need tools. Cleaning made a huge difference but after the cleaning fan it's run very smooth and quiet, Check the more details for services:
https://nemocleaning.com/handyman.html

2003 Chevrolet... | Answered on Jan 21, 2020


unplug the snapshot and send it back before it does even more damage! and google problems related to snapshot,you will find thousands of similar complaints!

Chevrolet HHR... | Answered on Jan 19, 2020


Most of them fasten on the bolts that hold your license plate on. Take the tail lights out and wire it to the back up lights. Then it should be wireless from there to the screen inside which you can hotwire t ok 13 volt or plug into a power port.

Chevrolet Cars &... | Answered on Jan 18, 2020


The dealer recommend GM Dex Cool Antifreeze.
But there are complaint against this type of coolant.
http://www.stevesnovasite.com/forums/archive/index.php/t-128547.html
In GM cars we replace Dex Cool with Prestone green coolant.
It's up to you. Ask before but if you decide to change the type of coolant then:
If your intention is to add coolant only, then you need:
Mix with
ANY COLOR ANTIFREEZE
ALL MAKES ALL MODELS
of cars and light trucks
add to ANY color antifreeze
PRESTONE
50/50
PREDILUTED ANTIFREEZE/COOLANT
EXTENDED LIFE up to 150000/mile 5 year protection.
DO NOT ADD WATER.

If your intention is to flush the RADIATOR (Cooling System), then you need:
Mix with
ANY COLOR ANTIFREEZE
ALL MAKES ALL MODELS
of cars and light trucks
add to ANY color antifrezze
PRESTONE
EXTENDED LIFE up to 150000/mile 5 year protection.
On the back you have to read directions:
Step 1 Drain. Step 2 Flush. Step 3 Fill.
Recommended to ad 30% to 50% volume, distilled water. If you flush the system and rinse with water you must add only 30% water to the antifreeze. There is more water trapped inside the engine compartment, because the thermostat is closed. Make sure to have a coolant density tester. When you finish one of 5 balls must sink, that indicates that you reached 50/50 strength. That means 50% Prestone and 50% Water, which will provide to your car a -34F degree FREEZE-UP Protection , and +265F degree BOILOVER protection.The next day,with a cooled engine open radiator cap, and test the strength of coolant. If not quite right, then siphon coolant from the radiator and add antifreeze, or distilled water as necessary.
Make sure to disposal the used coolant properly.

1997 Chevrolet... | Answered on Jan 18, 2020

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23401 Answers

Brad Brown

Level 3 Expert

18336 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...