Canon CanoScan - Recent Questions, Troubleshooting & Support

same problem with me i got Lide 20 Canon scanner - error code 2,7,0
any buddy know solution must let me know..
[email protected]

Canon CanoScan... • Answered on Feb 11, 2020

hi my printer this problem. release the lock switch detach the usb cable and reconnect. scanner driver will be closed code: 2,179,10

Canon CanoScan... • Answered on Feb 10, 2020

Perhaps you have forgotten to unplug the scanner before scanning? That's what happened to me. I kept getting different error codes, 5,202,63 or 5,202,52 or 5,202,54 and also a message that the driver was not in the TWAIN folder. According to the help file the problem might have been due to my nfts file system. I also tried downloading various new drivers. Nothing helped until I noticed that I had not unplugged the scanner!

Canon CanoScan... • Answered on Jan 20, 2020

The answere for me so far has been no. However I was successful with scanning in three documents for tennis scores today by installing the XP twain driver in MS Virtual PC in XP mode this installed all the drivers. But after the scanner powered down after timing out, nothing in my power could get it to work again for another document. To say the least I'm pretty Pissed about the whole thing. Knowing that as purchasers of these products were just left in the learch for upgrading to the latest version of windows and the manufacturer of the products can't be stuffed developing drivers for their products. Says a lot about Canon and their dodgy products and customer focus. Screw you Canon, I won't be buying your products again. Go with the times or get left behind!

Canon CanoScan... • Answered on Sep 13, 2019

Unfortunately, that's normal for this particular model. If you read the manual, or in this case the Quickstart Guide, you'll note that the top left corner is meant to go into the arrow corner. I'm annoyed with it too. You can always do it in Post-processing by doing two "turn image 90 degrees". If there would be a setting, it would be in the scanning program as the driver for this scanner has no settings available; you would have to check to see if there's a 'reverse image' setting in the program, though I doubt it.

Canon CanoScan... • Answered on May 08, 2019

how to release the lock swith to detack USB cable and reconnect?

Canon CanoScan... • Answered on Apr 11, 2019

I foun d this ..
I hope that will helped

Canon CanoScan... • Answered on Mar 07, 2019

Disconnect the usb (which is the power source) to the printer. Next, install the printer driver. If you don't have it handy, get it from the Cannon site where you will locate it by Computer model. Download it, double click upon it to install it. Keep an eye on the name of the file as you download it because you will have to find it on your computer.) Next, check that the driver was installed in Device Manager. (Look in Printers) After that, plug the usb back into the printer, powering it. Turn on the printer. Your computer should detect it shortly, automatically. If it does not, turn off everything. Turn back on the computer. Turn on the printer. Good luck.

Canon LiDE 120... • Answered on Feb 25, 2019

TO ANYONE READING THIS...I nearly took a hammer and smashed my Canon LIDE 110 Scanner cause I was so mad that it gave me this stupid error (5,202,52) no matter where I was connecting it and I thought it was done...THEN I just took another USB Cable (Like I have around 10 different USB Cables) ...AND IT WORKED! Try several USB cables before you give up on it...also don't start messing around with drivers and stuff, you could end up screwing up your system like I did...I hope this helps someone out there in the future with error 5,202,52 or 5,202,54, etc.Try at least 4-5 different USB cables before anything else..(If you want to know, I successfully used the USB cable with one of the fat black circle things on it (I think its for power or something), not just a straight usb cable. It's still a 5 pin USB cable however (Regular USB on one side, small 5 pin connecter on the other side))

Canon CanoScan... • Answered on Dec 30, 2018

If its for the LiDE 25 or similar model than try

It may work or it may not it all depends on the Operating System youre using on computer. The page lets you chose the OS.


Canon CanoScan... • Answered on Dec 02, 2018

Well I had a code 15 error with mine LIDE 20. Apparently the scanner needs a certain amount of power to run off the USB port. So I changed the USB port and problem fixed

Canon CanoScan... • Answered on Dec 01, 2018

I had the same problem. Solved it by going into the "CanoScan Toolbox" - "Settings" - and pressing the "Defaults" button in that panel - and then "OK" button. Afterwards everything worked fine. Hope this helps you.

Canon CanoScan ... • Answered on Nov 14, 2018

Not finding what you are looking for?

2,500 questions posted

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2345 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Cindy Wells

Level 3 Expert

6254 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Canon Office Equipment & Supplies

  • Forum

View Most Popular

  • Canon Office Equipment & Supplies