Canon Rebel - Recent Questions, Troubleshooting & Support

Use the "Video system" command in the Setup-2 menu to switch the video output between NTSC and PAL. This is for playing back your still photos on a TV.

If you're asking how to switch the 400D into video recording mode, the 400D doesn't record video. Sorry if that wasn't the answer you wanted to see, but that's the way it is.

Canon Rebel XTi... | Answered on Jul 09, 2019


I doubt about your camera having a Video mode. However you can check these settings for your Camera in detail.

Click on the link -> Camera Settings


Canon Digital... | Answered on May 30, 2019

Use a separate card reader instead of the camera. 58dd167.jpg

Canon Rebel XT /... | Answered on Jan 10, 2019

change your manual settings

Canon Rebel XT /... | Answered on Jan 10, 2019

Hi there! I suspect that your memory card is probably damaged. Did you try a different memory card? Postback so that we can proceed further..

Canon Rebel XT /... | Answered on Dec 01, 2018

I found the answer and fixed my flash. Look on

This will describe how, if you have been using a speedlite alot, than the little tab under the shutter release side of the hot shoe can get bent down thus constantly pressing down (toward the bottom of the camera) the small button which deactivates the pop-up1.gif flash even when the speedlite is not attached. Just bend the tab up a little with a jewler's screwdriver, turn the camera off and on and voila!! Fixed!!! Dan describes pushing the tab down, but on the xti, the tab needs to be bent up to release the flash deactivation switch and fix the problem. Thanks to Dan D on photonet for saving me a service call.

Canon Rebel XT /... | Answered on Dec 01, 2018

If this happens when your are shooting with a flash, check your falsh curtain settings.

Canon Digital... | Answered on Dec 01, 2018

Old cameras get this sticky handgrip problem.

Clean it with alcohol.

Canon Digital... | Answered on Sep 25, 2018

This is bad. Contact Canon customer support.

Canon REBEL T2i... | Answered on Sep 25, 2018

When you change the zoom, chances are the camera lose focus, and you need to half-press the shutter button again to the camera autofocus.

Its normal behavior to lose focus when zooming in or out.

Canon Rebel XT /... | Answered on Sep 25, 2018

If you ligthly press the shutter button then the screen with the settings must appear.
The same with the "Q" button.

Canon Rebel... | Answered on Sep 25, 2018

If this problem is not described in the troubleshooting section of the cameras's manual, then you need to contact Canon Customer Service, it's not a normal behavior, and probably is not something you can do yourself.

Canon EOS Rebel... | Answered on Sep 25, 2018

It can happen if you are in the Auto-No Flash mode. Or if the flash release button is stuck.

Contact customer service, and have a pro take a look at your camera.

Canon Rebel... | Answered on Sep 25, 2018

Maybe there's a problem with your camera's pop-up flash.

Contact Canon Customer Support, and see what they can do for you. Probably they will point where you can get your camera repaired.

Canon Rebel XT /... | Answered on Sep 25, 2018

Photography is the process of making pictures (graph) using light (photo)...
Light takes the most important role on produce nice pictures

There`re no fixed rules about photography, it`s an art so nobody have rights to say that the photo is good or bad...

During rainy day, you should prepare camera`s water-proof jacket or an umbrella to protect it against water. Some expensive cameras have been equipped with water-proof material.

Canon Rebel XT /... | Answered on Jun 22, 2018

No single fix im afraid, there are several fuses on the dc/dc converter that are worth checking, moisture on the flash board can fry them badly resulting in a dead camera.
basicly a dead eos is an eos with problems that wont allow the cpu to start, be it too much current being drawn somewhere, software issues or damaged ribbon cables.. risky business.

Best of luck

Canon Digital... | Answered on May 01, 2018

Most of the Time when this happens it's the curcuit board inside the lens that bad from use, Needs to be replace by a repair Tech! Try a different Lens to confirm that!

Canon Digital... | Answered on Feb 01, 2018

Not finding what you are looking for?

1,890 questions posted

Ask a Question

Usually answered in minutes!

Top Canon Cameras Experts

old marine
old marine

Level 3 Expert

2313 Answers


Level 2 Expert

69 Answers

Steven Wander
Steven Wander

Level 3 Expert

595 Answers

Are you a Canon Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Canon Cameras

  • Forum

View Most Popular

  • Canon Cameras