Cam Spray Garden - Recent Questions, Troubleshooting & Support


If you have enough room behind the stud wall install 1" rigid foam tape seams and then use the thickest possible roxsul insulation to fill the studs. Or axe the foam and install 6mil plastic on warm side of the wall after insulating tape all seams when done.

Cam Spray... | Answered on Sep 19, 2015


They are set at the factory if its dropped in pressure it couldhave popped an O . Ring. Check out.

Cam Spray 4000BT... | Answered on Sep 06, 2014


YOU HAVE A FLOAT IN THE CARBURETOR THAT MAY BE STUCK THERE IS A SMALL NEEDLE VAULE THAT ALSO MAY BE STICKING YOU CAN GET A REBUILT KIT FOR THE CARBURETOR

Cam Spray... | Answered on Jun 14, 2014


no I dont have manual

Cam Spray Cold... | Answered on Sep 23, 2013


Your unloader valve is not functioning. Take it apart and make sure it all the parts are able to move freely under the spring. You may need a new o-ring or two if you see damaged ones.

Cam Spray... | Answered on Jul 24, 2013


This is the best site to get ANY Honda manual, just send them a search request and within 2-3 hours you will hold your manual in your fingers.

Cam Spray Cold... | Answered on Jul 29, 2012


Okay!

just follow the power cord and unplug the damn socket from the electrical outlet!

Cam Spray... | Answered on Apr 27, 2011


It can be one of two things, either the valves in the pump or the unloader on the pump is having an issue. The first thing I would check is the unloader. If you look on your machine the big black handle that you screw up and down to regulate the pressure is where your unloader is located. I don't have the model number off the pump so I can't really walk you through repairing it, if you could get the model off the pump I will be able to give you a better idea on what to look for.

If this is not your issue it is going to be the valves in the pump that need to be replaced, for this I would also need to know the model number of the pump in order to give you some direction.

Cam Spray 1500A... | Answered on Nov 09, 2010


it is probley the connection is loose or a gasket need replasing

Cam Spray 1500A... | Answered on May 14, 2010


No need to re-invent the wheel when building your trailer mounted sprayer. Your local Northern tool Store, or at the address below,

http://www.northerntool.com/webapp/wcs/stores/servlet/category_6970_166839

you will find all the parts that you will need to complete your project. I have purchased several different types of sprayers, tanks, pressure pumps and parts from them over the years. They have a helpfull staff and most parts are in stock. Take a look at ready made trailer mounted sprayers there to pattern yours after then design in your special needs.
My first portable sprayer was made from four 55 gallon drums loaded onto the back of my pickup. For the pump I used a modified 2" trash/water pump reduced to 1' pipe then seven nozzles. Worked great however 220 gallons of water did not last very long. Problems began with the weight of water in large quantity. I decided I needed about 1000 gallons and found that I needed to deal with about 7500 lbs of weight. Oh well, enough already, good luck with your project and email if you have questions.

Cam Spray... | Answered on May 12, 2009


Request the diagrams from Cox.

Garden | Answered 36 minutes ago

Not finding what you are looking for?
Cam Spray Logo

18 questions posted

Ask a Question

Usually answered in minutes!

Top Cam Spray Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2481 Answers

john h

Level 3 Expert

23438 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Cam Spray Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...