Winter Sports - Page 7 - Recent Questions, Troubleshooting & Support

Hey Dave, Have you replaced the air filter? Try running it without the filter to see of that makes a difference.. bad gas will not cause this.. Sometimes its cheaper to take it to a professional..

It all depends where you live. But yeah winters are getting worse and worse. Global warming is not a myth

try using the choke...

I can't see the "box" you are referring to! It is cardboard, or made of wood, or plastic, or steel, or aluminum, or some other material?

I think on a worn startermotor. To be sure, give a little knock on the startermotor end when it won't start. If then it's good starter, then its the startermotor. If still not good, replace your battery.

For blackberry files import and export without screen, you can use blackberry link as well you can find blackberry blend services on your desktop pc and mac pc, you need to download it from official blackberry website. after download blackberry link, your blackberry mobile driver for pc already installed on your desktop or laptop, so you can easily browser from blackberry desktop application and aswell form your directly my computer page, there will show another disk as same as pendrive usb disk. Press Helpful Button after read Answer,

Certainly the carbs should be treated as a pair and so when one is suspected both should be checked. The cylinders will be unable to perform equally unless both carbs are tuned equally and synchronised at idle and at various throttle openings. As part of the checking process it is important to ensure both cylinders are capable of performing equally. A compression test has limited use and a cylinder efficiency test is better. Injecting compressed air into the cylinder would prove the effectiveness of the valve seats and piston rings. A small amount of leakage of the inlet valve seat would make little difference to a compression test but it would make a great deal of difference to the way the cylinder performs. Another important check is the valve clearances and also the ignition timing if it is adjustable. Some engines with twin ignition systems need to have the timing set for each cylinder.

Oslo Winter Park is just 30 min from downtown Oslo with some incredible slopes!!http://www.visitoslo.com/en/product/?TLp=12087&Oslo-Winter-Park

Reduce the idle RPM.

As far as I know, sleds have two directions. Forward and reverse. To make it go in the opposite direction, push it in that direction, or turn it completely around. God bless your efforts.

According to the specs it has carbs and auto oil injection.

Ski and snowboarding gloves protect your hands from both the cold and ski/snowboarding related injuries.

Clean the engine with a pressure washer and then run it and id the leak, no quick fix for this type of problem.

This is the same as doing any slider type CV carb, no matter the machine. Check the link. How to Carb Synching

taking that this a motor cycle then you have suffered what is known as" brake fade" to understand the term it works like this for brakes to work, kinetic energy ( spinning brake rotor) is converted to heat energy by the friction caused by applying the brake this loss of kinetic energy is the braking action or the bike slowing down normally there is enough heat transference to the passing wind but if the heat generated exceeds the heat transfer then the brakes and rotor will not absorb any more heat generated by the friction and so the brake stops working (like oil on the pads or linings) what cause it to happen-- there is clearance between the disc rotor and the brake pads but if the brakes are applied then the brake fluid is pushed out against the pistons and applies pressure to the rotor ( braking action) when the brake is released the fluid is returned to the reservoir and there is no problem BUT if that fluid is not allowed to return fully, the brakes remain on( your brake drag) and the heat generated besides going to the air , also heats and expands the brake fluid with nowhere to expand to , the brake is applied by the expanding fluid AS all brake fluids are hydroscopic( absorb moisture from the atmosphere) the water in the brake fluid boils off and you loose any pressure because the system is now full of air and air compresses when the brakes cool down the brake action comes back as the air has bled back to the reservoir The fix is to replace the master cylinder and the brake fluid and to ensure that the calliper slides freely on the mounting rods so that it self centres over the rotor what you have experienced is very common on heavy trucks on long down grades where the brakes over heat and fade resulting in control of the truck

That is the rev limiter kicking in.

U could get a new one

Water in tank or not enough spark or float is stuck

Damaged wiring and/or dirty or corroded wiring connections or switches seems likely. A wiring diagram would be a help in tracing the circuit of the hand warmers and during the process other problems will probably become obvious. It is easier to start by tracing a permanent fault than intermittent faults.

Find a wire that has 12 volts or more on it when the engine is running. Wire in you plug in connector to that, I would put an inline fuse in it also.