Check the Coin Mechanism:
Ensure that the coin mechanism is functioning correctly. Sometimes, coins may get stuck or not register properly. Verify that the coin slots are clear and that the mechanism is engaging properly.
If there's an issue with the coin mechanism, it could prevent the washer from starting. You might need to clean or repair it.
Inspect the Wiring:
There should be a harness with two wires that go into the coin mechanism box. Check if these wires are intact and properly connected. If you find any damage or loose connections, consider repairing or replacing the wiring.
Bypass the Coin Mechanism:
If you suspect that the coin mechanism is causing the problem, you can bypass it temporarily.
Cut the wires going into the coin mechanism and insert a push button switch in the line. This will allow you to manually start the washer without relying on the coin mechanism.
If you're unsure how to do this, consider contacting a local repair shop for assistance.
Check for Other Issues:
Inspect other components such as the lid switch, control board, and start button. Any malfunction in these parts could prevent the washer from starting.
Make sure the washer is plugged in and that there are no tripped circuit breakers or blown fuses.
Stale smells come from not drying the front gasket trough just inside the door. Your bleach isn't cleaning that area. Use Tilex Mold spray on it. Clean and dry the door glass as well and leave the door open for a few hours after a wash or leave it open all the time. If it is dry, it can't smell.There will always be some water in the pump area, but if you remove the pump filter cover, that releases and water left behind.When you use bleach always do whites or your tea towels next. You can also dilute by adding a couple of jugs of water first.There is a trick to look for rattling items between the inner and outer drum. Put a good flashlight against the holes in the drum and you can see what is below without getting the glare from the drum.These websites give you a full parts schematic showing all the parts and their positions.https://www.appliancepartspros.com/tub-basket-parts-for-whirlpool-wfw94heaw0.htmlWhirlpool Washer WFW94HEAW0 - OEM Parts & Repair Helppartselect.cahttps://www.partselect.caCanada Wide Same-Day Shipping For All In-Stock Parts. Shop Canadian And Avoid Customs ' 2 Million Parts Ready To Ship. OEM Parts & Accessories. One-Year Warranty. Money Back Guarantee. Free Repair Help & Videos. Types: Dishwasher Parts, Dryer Parts.
If it trips an earth leakage trip then that will probably be a damaged oven element.
Time for an electrician to replace the element or find another fault if it isn't that.
Question edited for clarity.
'then', a moment in time.
'than', a comparison between one thing and another.
It depends on the model, but usually related to the lid lock. Also check the breaker.
Why does my washer stop working after filling with water?
If the Top Load Washer stops after filling with water, be sure to check the house circuit breaker/fuse as well as the outlet and plug. Washers should be plugged into their own separate, dedicated outlet.
..
Fixya
https://www.fixya.com > ... > fisher paykel fault code 136
Now Error code 136 means you have a motor stall ... Question about GWL11 Top Load Washer. 1 Answer · What is fault code 136 on fisher & paykel ...
this is not a job for the faint of heart as you are taking the machine down to its component parts, removing bearings and seals and splitting the outer drum to get at the inner drum. No one has documented it on your model, but the videos will give you idea.
'top lip'? you mean a top load?
If it washes okay and the motor runs, it is likely the capacitor on the motor that does spin has failed,
Or the motor control board has failed.
Or the timer controller / main board has failed.
FULL 'make model (what it is)' in all questions please, first 3 words
I don't have real-time access to specific product information, including Maytag front load washing machines. However, I can provide you with some general information. The capacity of a washing machine is typically measured in cubic feet or kilograms and refers to the amount of laundry it can hold in a single load.
Question edited for clarity.
Check the water inlet solenoid. It sounds like it has failed. It should open and let the water in from an instruction from the controller..
https://www.google.com/search?q=Samsung+WW80v9+no+water
..
This could be down to a number of reasons. The most common of which is a displaced or faulty spin switch. This switch tell the machine that the lid is closed (or that the top is on a front loader). I know this may sound silly, but if you have a spin speed selector, double check to see that it's not been set to "0".
If neither of those work/fit the problem, and also if it is showing any error codes, eg. F01/F02/UNB, please let me know
A few possible causes:
Blocked Water Level Switch: Most top-loading washing machines utilize a pressure switch to tell the water when to shut off during a wash or rinse cycle. If the tube becomes blocked with minerals from hard water or if the switch itself goes bad, the water will never shut off.
Bad Water Valve: Valves at the points where the hot and cold water hoses enter your washing machine control the flow of water into the machine. If these valves become stuck open, or if their seals become lost or compromised, the water will continue to flow into the machine.
Faulty Controls: The controls might fail to acknowledge the input from the pressure switch and never advance from one cycle to another. In some cases, this is a voltage problem, while in other cases the controls themselves are bad and would need to be replaced.
If you've already cleaned and cut the ends of the tube going to the level sensor and the issue persists, it might be best to consult with a professional appliance repair service. They can help diagnose and fix the problem accurately. Please remember to turn off the water supply and unplug the machine before attempting any repairs.
It sounds like you've already tried several troubleshooting steps, but let's see if we can narrow down the issue with your Wascomat W655 commercial washer. Here are some additional things to consider:
Motor Capacitor: The motor capacitor plays a crucial role in starting the motor. If it's faulty, the motor might not engage properly. Consider checking or replacing the motor capacitor.
Motor Wiring: Inspect the wiring connections to the motor. Loose or damaged wires can prevent the motor from functioning correctly. Ensure all connections are secure and free from damage.
Motor Brushes: The motor brushes wear out over time. If they're worn down, the motor won't engage. Check the brushes and replace them if necessary.
Belt Tension: If your washer has a belt-driven motor, ensure that the belt is properly tensioned. A loose or damaged belt can cause motor issues.
Drain Pump: Although you mentioned that the drain pump seems to be working fine, it's still worth verifying. Sometimes a malfunctioning drain pump can affect other components.
Mechanical Obstructions: Inspect the drum and surrounding components for any obstructions. Something lodged in the drum or motor assembly could prevent movement.
High-Speed Spin: Since the issue occurs during the high-speed spin, focus on components related to this phase. It could be related to the motor, belt, or even the drum balance.
A professional technician could perform more advanced diagnostics.
If you haven't already, you might find it helpful to consult the diagrams and manuals specific to the Wascomat W655 washer. Alliance Laundry Systems provides replacement parts and repair resources. Diagrams, Parts and Manuals for Wascomat W655 Washer (alliancelaundry.com)
