Washing Machines - Popular Questions, Answers, Tips & Manuals

0helpful
1answer

No hot water supply available for WT-8071TTP LG washing machine

we do not put plumbing in for anyone
9/11/2021 10:18:46 AM • LG Washing... • 83 views • 0 helpful votes
0helpful
1answer

LG WD 1481-RD Washer/Dryer. Why is it taking an eternity to wash?

The loading sensor is not working and control panel issues and there could be issues with the water inlet valve which does pull the water into the appliance for every cycle.A person that fixes washing machines would need to have a look at your washing machine to see what the problem is.
9/9/2021 3:07:00 AM • Washing Machines • 73 views • 0 helpful votes
0helpful
1answer

Wm1814cw LG front load washer won't engage drain pump

Washer will not drain: The drain water pump is the main part in your washing machine that pumps out the water. If this is defective or has failed in any way, this will be the reason why your washer will not drain the water. Before you order a new drain pump, make sure to check the pump to be sure a small object like clothing or similar has not lodged itself inside of it causing the NO DRAIN issue and even a no spin issue?. If the drain pump is not clogged, you can test it with a multimeter and remove and replace if needed. Read more:  HYPERLINK "http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/" l "ixzz3X2LbXMWJ" http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/#ixzz3X2LbXMWJ The washing machine drain hose is where the water flows through to get the water out. If this drain hose is blocked, kinked, bent, or clogged, the washer will NOT be able to remove the water from the tub. Check the drain hose to be sure it allows the water to flow freely. You can take the drain hose off and run water through it in your sink to be sure it is not blocked. If there is water STILL in the washer when you remove the drain hose, grab a bucket as the water will exit from where you disconnected it The water pump belt (to drain out the water) may have broke or become frayed or loose. If this belt breaks then it is unable to drain and remove the water from your washer. Inspect the belt to see if this is causing the NO DRAIN issue and remove and replace if needed. If the lid switch is not working as required it will cause your washer to not drain (and many other problems). This may be unlikely as a bad lid switch will usually cause your washer to also not agitate or spin. However on some models this can vary. The best thing to do if you have a suspected bad lid switch is to test it. It can fail electrically and or mechanically. If mechanical failure is the issue, you should be able to see if it is cracked, broken, or not in place to make contact with the lid. To test it electrically, use a multimeter set on Ohms and test it for continuity My advice is free cuz God is good! doorswitchtestdryerdoorswitch-undefined-undefined-0_1.jpg doorswitch bypass-lid-switch-unplug-undefined-undefined-2_3.jpg water pump2-undefined-undefined-5_2.jpg washer-fills-and-drains-at-same-time-undefined-undefined-8.jpg
8/15/2021 1:06:24 AM • LG WM1814CW... • 113 views • 0 helpful votes
0helpful
1answer

Blomberg washer door lock symbol constantly on how can I get it off so I can open door normal way

There are two locks on them. Child Lock, C-On, and C-OFF. and Door Lock due to water level. The latter one should unlock a few minutes after the wash ends. If it doesn't, you need a service call. Cutting the power should reset it. https://www.google.com/search?q=Blomberg+washer+door+lock+symbol ..
5/25/2021 7:08:45 PM • Blomberg Washing... • 935 views • 0 helpful votes
0helpful
1answer

LG front loader. Why is it stuck on load sensing?

Pull the mains plug for 5 minutes. That is the closest you can get to a reset. Some do it by holding the On button as you connect the mains power. Continue to hold for 10 seconds and release. Aha, I just found this, and I was right. LG washer stuck on load sensing To reset this issue, the manufacturer advises to unplug the machine, press the Start-Pause button, and hold it in for 5 seconds before restoring power by plugging it into the outlet. Check for code clearance by completing a Run-Rinse cycle. Overloading specific gentle cycles can cause the error code to appears as well.

How to Reset an LG Washer ' Hunker

https://www.hunker.com > ... > Washer & Dryers
Search for: LG washer stuck on load sensing.
7/24/2021 2:26:17 PM • Washing Machines • 163 views • 0 helpful votes
0helpful
1answer

Frigidaire FFLE3911QW0 combo washer/dryer is starting and locking then it won't do anything else. Please someone help!?!

There are a couple of videos and text based articles in the link, plus disassembly. I would check connection on the control board connections and those on the lid lock. The lock has to be functioning properly to operate. https://www.google.com/search?q=Frigidaire+FFLE3911QW0+combo+washer%2Fdryer+is+starting+and+locking ..
9/19/2021 9:31:42 PM • Frigidaire... • 34 views • 1 helpful votes
0helpful
1answer

Bush Washing machine is not spinning quickly clothes are wet

If it is a top loader, it is a problem with the safety switch on the lid lock. If is is a front loader, you need a service call, it _may_ be the main board. FWIW, Bush make radios and televisions so they are not so good at washing machines.
7/24/2021 3:03:57 PM • Washing Machines • 121 views • 0 helpful votes
0helpful
1answer

My LG inverter direct drive front washer spin and temperature lights blinks continuously during cycle

https://www.youtube.com/watch?v=cm67V13_Bag
7/20/2021 6:25:08 AM • LG Washing... • 126 views • 0 helpful votes
0helpful
1answer

Model WM2277HW. In prewash cycle, why isn't detergent added from the prewash compartment in the dispenser?

1. Defective dispenser 2. Defective control board
7/20/2021 6:01:26 PM • LG Washing... • 115 views • 0 helpful votes
0helpful
1answer

Whirlpool Cabrio. Why an Sd code after shaft bearing replacement?

The Sd code indicates too much drag on the basket during the spin cycle. Since you just changed the bearings, make sure that everything from the motor to the basket hub is correctly aligned. Make sure that the drive basket hub doesn't have any worn splines. Check that the drain hose doesn't have any restrictions and that there are no clogs in the hose or the drain pump. There could also be a problem with the pressostat or the control board. I'd suggest you also check for any wires that got knocked loose or broken when you replaced the bearings. Usually the Sd code indicates there was too much detergent in the washer. The drain pump and motor are under strain from the excess bubbles. Super heavy towels can give the same error. I hope this helps. Cindy Wells
9/9/2021 6:45:44 PM • Washing Machines • 34 views • 0 helpful votes
0helpful
1answer

Hello. My Whirlpool fscr 80415 washing machine indicates error F34. What does this error mean? Thank you.

I am really glad I found this website! Your blog is an informative, helpful resource and vectorworks 2017 crack incl keygen it's great seeing more posts like yours. Keep up the good work with even better articles coming soon :)
9/22/2021 8:00:32 AM • Whirlpool... • 26 views • 0 helpful votes
0helpful
1answer

How do I repair a washing machine?

Common solutions for: Frigidaire Washer won't spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. If the lid switch assembly fails, the washer will not spin.
9/10/2021 12:01:26 AM • Frigidaire... • 32 views • 1 helpful votes
0helpful
1answer

E83 I only wash 1 bedsheet

The washing machine is unable to drain all of the water out from the drum then and their is an issue with drainage and the drum for your washing machine and it needs to be fixed from someone that repairs major appliances.
8/23/2021 2:30:37 PM • Washing Machines • 44 views • 0 helpful votes
0helpful
1answer

Fisher & Paykel toploader - drum leaning towards the right.

there are 3 to 4 spring assays that holds the drum from inside that need to be replaced every 2 to 3 years of using. ask the dealer for replacement parts and you can replace the assays by yourself easily by leaning the drum to one side and unhook the spring assay from the top then push it downside gently to unhook it from the bottom. Do them one-by-one and don't unhook all of them at once. hope this would help you
9/12/2021 5:14:53 AM • Fisher Washing... • 29 views • 1 helpful votes
0helpful
1answer

I have no power going into my washing machine

Possible fuse issue, you may replace it if not under warranty.
9/15/2021 2:37:43 PM • Washing Machines • 27 views • 1 helpful votes
0helpful
1answer

How to reset my Haier HLTW600axw Washing Machine?

Question edited for clarity. MAKE MODEL (WHAT IT IS) in all questions please. Category moved from Computers to Haier Washing Machines. It is a washing machine not a computer. There is not normally a reset. Sometimes just removing the mains plug will reset the logic board. Or, you press and hold the On Button as you plug in and hold for 6 seconds. My searching leads my to believe there is no reset. https://www.google.com/search?q=haier+hltw600axw+reset ..
8/23/2021 7:39:30 PM • Haier Washing... • 40 views • 0 helpful votes
0helpful
1answer

Samsung Washing Machine DWF45K6500A* Dispenser Drawer Assembly - Plastic cup stuck where softener goes

If you open the door, you may see screws that hold the top cover on the frame to the cabinet. Some model use screws and some use pressure clips that you cannot see. If it is pressure clips then the top is just pressed onto the rest of the cabinet and lifts off. IT can be a real challenge to not ding the paint trying to get the top to lift off. Once you do, you should be able to see the whole drawer dispenser. Attached link shows all the parts and views WF45K6500AV/A2 / 0000 Samsung Washer Parts & Free Repair Help - AppliancePartsPros
9/21/2021 12:53:01 PM • Samsung Washing... • 23 views • 0 helpful votes
0helpful
1answer

Samsung front loader. Why does filter only click when rotated counter-clockwise?

Those filters do screw out. There may be grooves that have to line up. Keep turning counterclockwise slowly and pulling outward firmly. https://www.ntgdsightglass.com
7/25/2021 6:19:38 PM • Washing Machines • 78 views • 0 helpful votes
0helpful
1answer

Electrolux EWW1486HDW. Every time it's turned on, why does it go straight to 1 minute, then locks and unlocks?

Probably cycle timer and/or control board issues
9/7/2021 9:16:46 PM • Washing Machines • 29 views • 1 helpful votes
0helpful
2answers

What year is my kenmore washer model 110-25132411, serial # C54040367

You can determine the age of your appliance by looking at the serial number on the nameplate. The first number indicates the year of manufacture, and the second and third digits indicate the production week.
8/17/2021 3:39:49 PM • Kenmore Washing... • 45 views • 0 helpful votes
Not finding what you are looking for?
Washing Machines Logo

262,604 questions posted

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Brad Brown

Level 3 Expert

18805 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...