Washing Machines - Page 4 - Recent Questions, Troubleshooting & Support

Video says is is low AC voltage. https://www.google.com/search?q=IFB+Front+Load+Washing+Machine+with+P13+error ..

Hi. Haas deluxe top load washing machine we got EU error code so what i need to do

Yes, the most likely reason is that the pipe has a blockage, the bore isn't large enough, you have an airlock with water in it, or the fall into the waste pipe isn't steep enough. When it senses any back pressure it faults. ..

Good Morning Anonymous, this is Z. I am happy to assist you! I understand that your door indicates it is open and your dryer will not operate. Let's attempt resetting your dryer by either unplugging it or flipping the household circuit breaker off. It is good to wait approximately ten minutes and turn on your dryer. Select a normal cycle and verify if your dryer will start. If your dryer will not operate then it possibly have a faulty door lock assembly or a communication problem with the control board. At this point, it would be advisable to contact an experienced appliance repair tech to assist further.

Yes you must change ziner diode in maine power board..

If your Hisense top-loading washing machine is not washing but can spin out the water, it could be caused by a few different issues. Here are a few things you can try to fix the problem:

1. Check to ensure that the washing machine is properly loaded and balanced. An unbalanced load can cause the machine to stop working or not wash properly.
2. Check the water supply to the machine. Make sure that the water hoses are properly connected and that the water supply is turned on.
3. Check the detergent dispenser to make sure that it is not clogged. A clogged dispenser can prevent the detergent from being dispensed and the machine from washing properly.
4. Check the lid switch. If the lid switch is faulty, the machine may not wash but will spin out the water.
5. Check the water level switch. If the water level switch is faulty, the machine may not wash properly but will spin out the water.
6. If the problem persists, consider contacting Hisense customer service or a technician for further assistance.

It's essential to note that if the machine is not washing but it can spin out the water, it could be caused by a malfunction or damage in the water level switch, the timer or even the motor.

Question edited for clarity, full name of maker and add CAPS. Washing Machines Category is probably not the best place for this Wolfgang Puck Convection Oven. :>D There is ZERO support for Puck's Chinese products, except where people strip them for spares on eBay. They cover warranty and then nothing. Wolfgang has nothing to do with the items, he just gets commission on sales for having his name on them. https://www.google.com/search?q=wolfgang+puck+BTOBROO15+parts You can however buy them to pattern as they are all made in the same Chinese factory and sold to OEM manufacturers and also sold via many spares suppliers. Check out the huge selection in the link. https://www.google.com/search?q=oven+timer+control+knob&tbm=isch&ved=2ahUKEwjz7f349oCFAxXgwhQJHbioCucQ2-cCegQIABAA&oq=oven+timer+control+knob&gs_lp=EgNpbWciF292ZW4gdGltZXIgY29udHJvbCBrbm9iSMYpUKUMWK8jcAB4AJABAJgBXqABiASqAQE2uAEDyAEA-AEBigILZ3dzLXdpei1pbWfCAgUQABiABIgGAQ&sclient=img&ei=1dX5ZbOvOOCF0_gPuNGquA4&bih=919&biw=1920&rlz=1C1QJDB_enCA643CA644 ..

The rod which controls the flow of water to the various compartments needs to be adjusted. It is not a difficult fix. You can contact Malber usa ([email protected]) and they can "walk" you through it. In the alternative, you can put the detergent in the pre-wash tray without concern.

Have youtried contacting the store you bought it from or going directly to the manufacturer? These are a good starting point for part like that.

Dishwas machine

Your NOT suppose to "Program anything". Machines are kinda like people. After they work, they need "some" time to rest. Your machine (And Mine) all do this. Next time leave it alone, the minute will count down and it will automatically shut off. Question? You actually stood by the machine and watched the entire cycle? Was there another problem that motivated you to do this? Like your clothes were still wet or water still in the tub? If you need further help, reach me via phone at https://www.6ya.com/expert/steven_b77d19396bfe2249

Door latching or lock error ·Door not detected closed ·Check door is closed ·Check door catch and latch ·Check door lock wiring Check door lock

It would be innapropriate to recomend the removal of a safety device. I would repair it, not remove it.

If your Indesit IWDD7143 washing machine is trying to operate the inlet valve during the dry cycle, there could be a few potential reasons for this issue:

Not a Washing Machine and too specialized for Fixya. There is nothing online regarding Error 3. Contact their Support phone line direct. https://www.mt.com/ca/en/home/service/support-and-repair/support.html https://www.google.com/search?q=mettler+toledo+FP90+error+03+error ..

A few possible causes: Blocked Water Level Switch: Most top-loading washing machines utilize a pressure switch to tell the water when to shut off during a wash or rinse cycle. If the tube becomes blocked with minerals from hard water or if the switch itself goes bad, the water will never shut off. Bad Water Valve: Valves at the points where the hot and cold water hoses enter your washing machine control the flow of water into the machine. If these valves become stuck open, or if their seals become lost or compromised, the water will continue to flow into the machine. Faulty Controls: The controls might fail to acknowledge the input from the pressure switch and never advance from one cycle to another. In some cases, this is a voltage problem, while in other cases the controls themselves are bad and would need to be replaced. If you've already cleaned and cut the ends of the tube going to the level sensor and the issue persists, it might be best to consult with a professional appliance repair service. They can help diagnose and fix the problem accurately. Please remember to turn off the water supply and unplug the machine before attempting any repairs.

It's recommended to call Bosch Customer Support at 1-800-944-2904 and specify the exact error code when calling. Good luck.

That's coil sensor. Just replace it and you'll be back in business...

We don't have these strange machines in north America. If it is new it is under warranty and needs a claim. It sounds like the main board has failed, or the timer. Not finding that model https://www.google.com/search?q=Super+General+Washing+Machine+SGW10225 ..