Tools & Hardware - Others - Recent Questions, Troubleshooting & Support


Gi?m gi? cung c?p l?m ??p
12799086-undefined-undefined-0.jpg

Tools & Hardware... | Answered on Dec 06, 2019


I'm assuming your talking about drywall that was wet during a flood of some type? Recommend you remove all damaged drywall and using a straight edge and a utility knife this can be easily accomplished. After you cut and remove the damage, remove all screws or nails from the studs giving a good surface for the new drywall that your going to replace the damaged stuff with. Get that done and we can move onto taping and drywall compound repairs. Hope this helps.

Tools & Hardware... | Answered on Dec 06, 2019


Could be a defective switch

Dewalt Tools &... | Answered on Dec 05, 2019


Contact Stanley directly to inquire OR check with a dealer who handles the product.

Stanley Tools &... | Answered on Dec 03, 2019


I'm not familiar with that particular model, but they are virtually all replaced the same way. There are a few screws through the pad into the base. Simply remove them and screw the new pad on. You'll see that it's quite simple once you get the new pad in your hands.
Just be careful not to strip the head of the screw: use the right size screwdriver tip.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread. If I've managed to answer your question or solve a problem, please take a moment to kindly rate this post....thanks!

Bosch Power... | Answered on Dec 02, 2019


Scaffolding systems require the use of many accessories. Base jacks, U-head jacks, fork heads and adjustable fork head jacks, v-pressings, c-cups and make up some of the necessary accessories of a scaffolding.

Tools & Hardware... | Answered on Nov 29, 2019


CAN ONLY GUESS THAT PERHAPS THE MANUFACTURER

Sander Tools &... | Answered on Nov 27, 2019


The staples probably can be obtained from a Stanley Sharpshooter Electric Heavy Duty Stapler dealer.

Stanley Tools &... | Answered on Nov 27, 2019


You can order one off of Amazon here:
https://www.amazon.com/Swingline-Staples-Optima-Heavy-Length/dp/B00006IFMB/ref=sr_1_5?keywords=3%2F8+inch+staple&qid=1574637921&sr=8-5

Staples Tools &... | Answered on Nov 24, 2019


weet U zeker dat er toch niet ergens een nietje of iets anders im de lade zit ?

Staples Tools &... | Answered on Nov 23, 2019


You should not need any tools to lift the guard/nose piece. The T5 nose piece cleary has engraved on it "Pull Up To Insert Staples". To remove old staples, use a pencil or similar rod to depress the hammer/striker above the staples while the nose is open.

Stanley Tools &... | Answered on Nov 20, 2019


Sure, you can purchase them on amazon, here: Aurora Smart Technology JamFree Paper Shredder I hope this was Helpful. Cheers

Desa... | Answered on Nov 20, 2019


Didnt give much info to go on lol. Make /model and a little more detail on your issue will be needed before anyone can try to help you

Tools & Hardware... | Answered on Nov 13, 2019


YOU ARE USING TOO MUCH AIR PRESSURE

Stanley Bostitch... | Answered on Nov 13, 2019


If the threads on the nut or shaft are stripped, the nut will turn freely and it can be removed with pliers by turning and pulling at the same time. If it won't turn, it is probably galled or cross-threaded. In that case, try penetrating oil first. If that doesn't loosen it, try heating the nut with a butane or mapp gas torch. Good luck.

Dremel Tools &... | Answered on Nov 13, 2019


In all ro systems filtering sea-water or brackish water, there should be much more waste water than potable water produced. You didn't say if the system is producing potable water. If you can give more information about your inlet water and the quality of your potable water quality I may be able to help.

Tools & Hardware... | Answered on Nov 13, 2019


I had the same problem, The problem is that the tumbler lid is to smooth and there is no grip from the spinning wheel. I solved this problem by taking a kitchen steak knife and roughing up the edge of the tumbler where it rides on the spinning wheel. Works great now. Best of luck

Rotary Thumlers ... | Answered on Nov 11, 2019

Not finding what you are looking for?
Tools & Hardware - Others Logo

14,708 questions posted

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Brad Brown

Level 3 Expert

18121 Answers

john h

Level 3 Expert

22486 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...