Saws - Page 9 - Recent Questions, Troubleshooting & Support

Hi, please check your local home depot or lowers for the part. You can call them or search their website for the product. Thank you.

Hi, In this case, it might be best to reach out to the manufacturer in order to get find the safe and most affordable replacement for your bandsaw. If you don't want to use that route, please reach out to your local Home Depot store via phone to have them check their catalog of products for your gear. Thank you.

limited info generic answer check tesioner refer to your manual on adjustment

Blade guards are spring loaded so they will not stay up unless you hold it up manually

There is a button on the saw that holds the shaft still. Unplug the saw and put light pressure on this button while you slowly turn thr blade by hand. When it gets to the hole, the button will drop into the shaft. Keep it pressed down and unbolt the nut.

Greetings from Toronto - ish. I am in Canada so my searches are normally weighted to Canadian suppliers. In this case none are .ca However Repair Clinic do supply to Canada and have a 1-800 number that states it on the Contact page. https://www.google.com/search?q=terratek+sliding+mitre+saw+parts ..

the belt shape new will not effect replacing it. It does not stretch but slides on. Did you loosen screw? Refer to instructions page 19-20. Tey calling the number listed in instructions. https://www.manualsdir.com/manuals/79545/elektra-beckum-kgs-303.html?page=19 ..

Question moved from Bosch Computer, to Bosch 4000 table saw. Unplug the unit and turn the blade by hand. Check the blade is tight and running true. See if the blade is touching anything. If you can't see anything wrong there, it make be the carbon brushes in the motor.

direct from Delta would be the place to look

ever think perhaps it needs oiled

The links in here says there is. https://www.google.com/search?q=Model+3320445+compressor+reset ..

First, I'm not a "Benchmark" representative. * Check your warranty. Call for support. * Amazon supports "Benchmark Abrasives"; https://www.amazon.com/stores/node/7925658011?_encoding=UTF8&field-lbr_brands_browse-bin=Benchmark%20Abrasives&ref_=w_bl_hsx_s_hi_web_7925658011 *** Following is for information only.*** * Review; https://modernwoodworkersassociation.com/penultimatewoodshop/2013/04/benchmark-miter-saw-station-review.html * Forum review of 3" saw ; https://forum.canadianwoodworking.com/forum/tools/power-tools/30520-benchmark-3-circular-saw * Facebook (knife, blades); https://www.facebook.com/Benchmark-Knife-Saw-1514585088757599/ * Ebay; https://www.ebay.com/sch/i.html?_from=R40&_trksid=m570.l1313&_nkw=benchmark+saw&_sacat=0 Aloha, ukeboy57 Additional related info; * Master force; https://hw.menardc.com/main/items/media/SUMEC001/Install_Instruct/240-0021MasterForce10InchMiterSawOwnersManual2015.pdf * Ridgid; https://images.homedepot-static.com/catalog/pdfimages/97/97714f37-7bbc-4393-89c2-1874e976b0de.pdf * Porter Cable; http://pdf.lowes.com/useandcareguides/000999115006_use.pdf * Craftsman; https://c.shld.net/assets/own/00921236e.pdf

Can you get a compression tester to check the compression? With the throttle wide open, the choke OFF, and the decompression valve (if so equipped) NOT engage, pull the engine over 3-5 times or until the gauge quits rising. You would like to see 90psi or more and if it is at 60 or less then it is most likely a scored piston and cylinder or bad rings. If the compression is good you need to check for spark. If it has good spark then it will most likely be fuel related. Often a complete tear down and rebuild of the carb is what is required.

I have been fixing table saws, compressors and other tools with similar motors for several years and I have never been able to find anyone who sells just the thermal switch on these motors. I usually use one from another motor that's burned out if I need one. You'll have to find a repair center that has motors they could take one of these switches out of and sell/give to you. Otherwise, it's a new motor to get one.

First thing I would check are the Carbon Brushes. The are # 75 in the picture



Hope this answers all your questions
Please remember to Rate/vote for any solution that helps you out.
Thanks for using Fixya.

They are a reliable saw. Presumably you are replacing the piston and rings and honing the bore. Strip and clean the carburetor. Replace the spark plug and lead. https://www.google.com/search?q=MAKITA+7301+SAW+full+service ..

Parts suppliers https://www.google.com/search?q=terratek+12%22+sliding+compound+miter+saw+parts ..

Thanks your question. please see this video

https://search.yahoo.com/search?fr=mcafee&type=E211US1494G0&p=jepson+saw+9210+manual They have a site to contact them.

https://diy.stackexchange.com/questions/187271/ryobi-circular-saw-motor-runs-blade-doesn-t This may help you.