Music - Page 5 - Recent Questions, Troubleshooting & Support


seems to be a standard acoustic setup to me. If it doesn't have all the string pins in it, you'll need to get some. you simply pull out the pin, put the string in, then wind it up on the machine heads (tuners) On this one you may need to put the strings through from the inside, I'm not sure about this particular model. I like a double wrap to start on the bass strings, but that's a choice I make. You could go with nylon strings, get ball end, they're easier to use than plain. It takes a bit of know how to do plain, thy have to be wrapped just right on the pins.

Yamaha Music | Answered on Nov 02, 2019


Korea, 1996, July as best as I can make out from https://forum.gibson.com/topic/139846-epiphone-serial-number-decoding/
without knowing the model and the condition, there's no telling what it's value is. Check reverb.com for similar guitars
safe to say tho that a Korean made Epiphone is not a classic (pre-Gibson) and will not be a high value guitar.

Epiphone Music | Answered on Nov 02, 2019


Are you sure you have the model name correct? I see all kinds of Dean Edge basses, but no mention anywhere of a Forage. How old is this model?

Bass Music | Answered on Oct 31, 2019


Broken cable inside, possibly at the output jack?
Or a failed potentiometer (volume or tone)
Pull the back plate off, and have a look at the wiring, Trace it with an ohmmeter to check for continuity at each step.
https://www.premierguitar.com/articles/23496-guitar-shop---five-ways-to-use-a-digital-multimeter

Bass Music | Answered on Oct 31, 2019


If no fuse holder is evident on the rear panel, check for an open fuse inside.

Casio Music | Answered on Oct 31, 2019


I have a PSR-E323 and to connect it with my pc using a MIDI connector should i install driver from http://download.yamaha.com/usb_midi/ ??? I tried to install that.. An error msg popped up... error 25001 no device is connected. connect a device and try again. If the "found new hardware" wizard appears push the cancel button...What should I do?? Help me pls...

Yamaha PSR-E323... | Answered on Oct 30, 2019


You need to replace the power resistor R54:
http://gisywall.blogspot.it/2016/01/zoom-g1xn-continuously-shows-bt-on.html

Samson ZOOM G1x... | Answered on Oct 28, 2019


You may find one if you google it.

Yamaha Music | Answered on Oct 27, 2019


Hi
If you are talking about cleaning the rubber contacts I wouldn't bother. Once they start to fail then it is best to replace them. You can do this either for the octave giving problems or best to replace complete set. Main part is VY84670R your piano has 6 octaves of these. with a shorter part at either end.

Yamaha Music | Answered on Oct 24, 2019


Electric guitars generally have a lower action (strings are closer to the neck), lighter gauge strings and easier access higher up the neck. All these things make them physically easier to play. Also with the addition of an amplifier it means you don't have to work as hard to get a louder volume.

However if you get a nice acoustic that is setup well, they can also be a pleasure to play.

What you choose I think should be dictated by what music you like.

Electric Music | Answered on Oct 24, 2019


If you have any cables from the effects inserts section of the board inserted, disconnect them. Check ALL sends levels. Check effects processor for L.E.D. signal. .(Assuming you are using the internal effects.)
Here is an excerpt form the manual:
https://assets.peavey.com/literature/manuals/80301359.pdf

Peavey Music | Answered on Oct 23, 2019


See if another audio source connected to the mixer produces the same results. Try with the same cable and then with another cable. The purpose of this procedure is to determine if it is the cable and/or the laptop. (Sound card problem???) or mixer.
Is it ALL audio or just specific audio from for instance, a music application? Does it cut out using iTunes?
The mixer may have a bad or oxidized input. Try a different input channel? Are you using headphones to listen? It may be the headphone amp? OR, if audio is produced via amped speakers, it may be the mixer output. Does the mixer have metering? Do the meters also cut out? Does the laptop do the same thing if plugging in headphones to the laptop directly (no mixer)?

Behringer Music | Answered on Oct 23, 2019

Not finding what you are looking for?
Music Logo

23,144 questions posted

Ask a Question

Usually answered in minutes!

Top Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Brad Brown

Level 3 Expert

18157 Answers

Are you a Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...