Miscellaneous - Popular Questions, Answers, Tips & Manuals
LG 86UM8070AUB bottom half of TV not updating
It sounds like you have already tried some troubleshooting steps, such as disconnecting each LVDS cable and replacing the tcon. Since those steps did not resolve the issue, getting the main board replaced is a good next step. If that does not fix the problem, it could be a more complex issue that requires professional repair.
3/19/2023 2:25:27 PM •
Miscellaneous
•
90 views • 0 helpful votes
I have toshiba refrigerator inverter GR-A525ABEZ not working and lamp also
If your Toshiba refrigerator inverter GR-A525ABEZ is not working and only the Eco mode light is blinking, there may be a problem with the fridge's compressor or control board. Here are some steps you can take to troubleshoot the issue:
Check the power supply: Ensure that the refrigerator is properly plugged in and that the power outlet is working. Try plugging in another appliance to the same outlet to confirm that there is power.
Check the control board: The control board manages the refrigerator's functions and may be malfunctioning. Unplug the refrigerator and wait a few minutes before plugging it back in. If the Eco mode light continues to blink, the control board may need to be replaced.
Check the compressor: The compressor is responsible for cooling the refrigerator and may be damaged or malfunctioning. If the compressor is not working, it will need to be replaced by a qualified technician.
Check the lamp: The lamp may have burned out and need to be replaced. This can be done by removing the old lamp and replacing it with a new one.
If none of these steps resolve the issue, it's best to contact a qualified technician for further diagnosis and repair.
3/20/2023 4:47:04 AM •
Miscellaneous
•
32 views • 1 helpful votes
Frigidaire gallery refrigerator lights blinking continuously like disco lights
The EF code typically indicates a problem with the evaporator fan motor or a sensor related to the fan. Since you already replaced the evaporator fan motor and the code didn't go away, it's possible that there is still an issue with the sensor or with the wiring that connects the fan to the control board. You may want to check the wiring and make sure all connections are secure.
The blinking lights inside the fridge could be a sign of a problem with the control board. When you replaced the control board, did you make sure to program it according to the manufacturer's instructions? If the programming isn't correct, it could cause the lights to blink.
It's also possible that the new control board is defective or not compatible with your particular refrigerator model. You may want to double-check that you have the correct part number and that it's designed for your specific model.
If you've tried all of these troubleshooting steps and the problem persists, it may be time to call in a professional technician to diagnose and repair the issue.
3/20/2023 7:07:20 PM •
Miscellaneous
•
29 views • 0 helpful votes
How do I connect a spectroniq PLTV 32050 (2006 television) to dish network and program the stations?
To connect your Spectroniq PLTV 32050 TV to your Dish Network receiver and program the stations, you can follow these steps:
- Connect your Dish Network receiver to your TV using an HDMI or RCA cable. Make sure the TV is turned on and set to the correct input source.
- Turn on the Dish Network receiver and follow the on-screen instructions to complete the setup process.
- Use the Dish Network remote to program the stations. Press the "Menu" button and navigate to the "Programming" or "Channels" section. Follow the on-screen instructions to scan for available channels and save them to the receiver.
- Once the channels have been saved to the receiver, use the "Input" or "Source" button on the TV remote to select the input source that the Dish Network receiver is connected to.
- Use the TV remote to adjust the picture and sound settings to your preference.
If you have any trouble with the setup process, you can refer to the user manual for your Dish Network receiver and your Spectroniq PLTV 32050 TV for more detailed instructions.
3/19/2023 7:38:43 PM •
Miscellaneous
•
27 views • 0 helpful votes
Krups EA829810/70L-2317 - does not turn on
If your Krups EA829810/70L-2317 coffee machine is not responding when you press the power button, there are several possible causes for this issue:
- Power supply: Check to make sure that the coffee machine is properly connected to a power source and that the power outlet is working. You can test the outlet by plugging in another device to see if it works.
- Fuse: If the coffee machine is connected to a power source and still not turning on, there may be an issue with the internal fuse. You can try replacing the fuse to see if that resolves the issue.
- Power button: It is possible that the power button itself is damaged or malfunctioning, preventing the machine from turning on. You can try cleaning the power button or contacting Krups technical support for further assistance.
- Internal components: If none of the above solutions work, there may be an issue with one of the coffee machine's internal components, such as the circuit board or motor. In this case, it is recommended that you contact Krups technical support or a certified repair technician for assistance in diagnosing and repairing the issue.
I hope this helps!
3/22/2023 2:30:35 PM •
Miscellaneous
•
25 views • 0 helpful votes
My Reizen atomic watch, radio control LED Toplight,Item Number 712180, DC03/22B,
I'm sorry to hear that your Reizen atomic watch is not updating to daylight savings time. Here are a few things you can try to troubleshoot the issue:
- Make sure that your watch is set to the correct time zone. If it's not set to the correct time zone, it may not be able to receive the correct signal to update for daylight savings time.
- Check to see if the watch is receiving a signal from the atomic clock. Atomic watches rely on radio signals from atomic clocks to update the time and date automatically. If your watch is not receiving a signal, it may not be able to update for daylight savings time. Try moving your watch to a different location to see if it can receive a signal.
- Check the battery level. A low battery can affect the watch's ability to update for daylight savings time. If the battery is low, replace it with a fresh one.
- Contact the manufacturer or retailer for further assistance. If none of the above steps work, the watch may be faulty and you may need to contact the manufacturer or retailer for further assistance.
I hope these tips help you resolve the issue with your Reizen atomic watch.
3/19/2023 4:35:56 PM •
Miscellaneous
•
26 views • 1 helpful votes
My 1994 Ford F150, 4 x 4, 5.0 will not start below 40
have you measured battery voltage at the battery terminals ( not on cable clamp) while trying to start? Have you inspected the cable clamps for corrosion and and damaged wiring. Have you measured voltage on starter motor while trying to start the vehicle?
3/22/2023 2:02:57 AM •
Miscellaneous
•
24 views • 0 helpful votes
No video output at all on Panasonic TX-43FX650B
Check the connections: Make sure all the cables are securely connected to the TV and the external devices, such as a cable box or game console. Try unplugging and replugging the cables to ensure a good connection.
Check the power source: Make sure the TV is plugged in and the power outlet is working properly. You can try plugging in another device to the same outlet to check if it's functioning.
Check the input source: Verify that the TV is set to the correct input source for the device you're trying to use. Use the "Input" button on the remote to cycle through the available input sources.
Check the settings: Make sure that the picture settings on the TV are set correctly. Try resetting the picture settings to the default settings and see if that helps.
Perform a power cycle: Turn off the TV and unplug it from the power outlet. Wait for a few minutes and then plug it back in and turn it on again. This can sometimes reset the TV and fix the issue.
Update the software: Check if there are any available software updates for the TV and install them if needed. This can sometimes fix software-related issues that are causing the video output problem.
If these steps do not resolve the issue, you may need to contact Panasonic customer support or a professional technician to further diagnose and fix the problem.
3/20/2023 1:30:31 PM •
Miscellaneous
•
24 views • 0 helpful votes
Does HICET offer proper placements for students?
Placements at HICET have been average for mechanical, electrical, electronics and computer. There was no placement for aeronautical department. Also the companies that came were local companies.
3/18/2023 9:45:22 AM •
Miscellaneous
•
24 views • 5 helpful votes
Remove master control block from edge mini tablet from access corrections/Keefe Group
Moreover, it is important to note that removing the master control block from a device can potentially render it unusable and may violate any terms of use or legal agreements with the manufacturer or service provider.
If you are experiencing issues with your device or have concerns about its security or privacy, I recommend contacting the device manufacturer or service provider for assistance or seeking advice from a qualified technician or IT specialist.
3/20/2023 10:27:56 AM •
Miscellaneous
•
23 views • 0 helpful votes
Where is the fuse on a Miele G692 SCI PLUS -3 Dishwasher?
The Miele G692 SCI PLUS -3 Dishwasher does not have a traditional fuse that can be replaced by the user. However, it does have a safety switch that may have been tripped, causing the dishwasher to stop working. The safety switch is typically located on the underside of the dishwasher and can be accessed by removing the kick plate at the bottom of the dishwasher. If the safety switch has tripped, it can be reset by pressing it back into place until it clicks. If this does not resolve the issue, it is recommended to contact a Miele service technician for further assistance.
3/18/2023 10:13:52 AM •
Miscellaneous
•
23 views • 0 helpful votes
I dropped my Nokia 2760 Flip in water
Disassemble the phone and look for corrosion using high-power (> 10x) magnification. Rinse with distilled water and blow it dry. Make sure the connector to the display cable is clean and dry inside. Note: patching corroded circuit traces requires considerable skill at soldering, and a very fine soldering iron tip. Likewise, replacing corroded cell phone components is not a task for rookies.
3/13/2023 1:00:57 AM •
Miscellaneous
•
25 views • 0 helpful votes
My Toshiba 55lf621u19 tv has 5v1 and 5v2, and i only have 5v on number 1 is the power supply board bad or possible 5v2 isnt used?
It's possible that the 5V2 rail on your Toshiba TV power supply board is not being used, and that's why you're only seeing voltage on the 5V1 rail. However, it's also possible that the power supply board is faulty and not providing voltage to the 5V2 rail.
To determine if the power supply board is faulty, you can use a multimeter to measure the voltage at the connector for the 5V2 rail. If you're not getting any voltage there, it could indicate a problem with the power supply board. However, if you do see voltage on the 5V2 rail, it's likely that it's just not being used.
You can consult your TV's user manual or contact Toshiba's customer support for more information about the purpose of the 5V2 rail on your TV's power supply board.
3/17/2023 7:47:59 PM •
Miscellaneous
•
23 views • 0 helpful votes
Why is our indicator light keep showing the bag is full
There could be several reasons why the indicator light on your Clark Carpet Master vacuum cleaner is still showing that the bag is full even though you've put in a new bag. Here are some possible causes:
Sensor issue: The vacuum cleaner has a sensor that detects when the bag is full. If this sensor is malfunctioning, it may continue to show the bag as full even if it's not.
Clog in the hose or filter: If there is a clog in the hose or filter, the vacuum cleaner may not be able to pull air through the bag, which could trigger the bag full indicator.
Incorrect bag installation: It's possible that the new bag wasn't installed correctly. Make sure that the bag is securely fastened and that there are no gaps or openings where air could escape.
Faulty indicator light: Finally, it's possible that the indicator light itself is faulty and needs to be replaced.
To troubleshoot the issue, try the following steps:
Check the hose and filter for any clogs. Clear any blockages you find.
Double-check that the bag is installed correctly.
If the issue persists, try replacing the bag again with a different brand or type.
If none of the above steps resolve the issue, it may be necessary to take the vacuum cleaner to a repair shop to diagnose and fix the problem.
3/17/2023 4:04:15 PM •
Miscellaneous
•
23 views • 0 helpful votes
My Panasonic TV won't turn on green light is flashing
If the green light is flashing on your Panasonic TV and it won't turn on, it usually indicates that there is a problem with the TV's power supply. Here are some troubleshooting steps you can try:
Unplug the TV from the power outlet and wait for a few minutes before plugging it back in. This will allow the TV to reset.
Check the power cord and make sure it is securely plugged into the TV and the power outlet. If the cord is damaged, replace it.
Check the power outlet by plugging in another device to see if it works. If the outlet is not working, try plugging the TV into a different outlet.
If the above steps do not work, you may need to contact a professional technician to diagnose and repair the TV. It could be an issue with the power supply or other internal components.
I hope these steps help you resolve the issue with your Panasonic TV.
3/20/2023 9:34:21 AM •
Miscellaneous
•
22 views • 0 helpful votes
Can someone help me with a calibration guide for a David White ael 2500 laser level
Here are the steps you can follow:
Set up the laser level on a flat surface or tripod and turn it on.
Place a target or receiver on a wall or surface where you want to project the laser beam.
Adjust the receiver to the same height as the laser level.
Align the laser level with the target or receiver.
Rotate the laser level 180 degrees and align it with the target or receiver again.
Check the readings on the receiver. The difference between the two readings should be less than or equal to the accuracy specification for the laser level.
If the readings are not within the specified accuracy, adjust the laser level until they are. Use the adjustment screws on the laser level to fine-tune the alignment.
Repeat the calibration process if necessary.
Note: Before calibrating your laser level, make sure it is clean and free from any debris or damage that may affect its accuracy. Additionally, consult the user manual for specific instructions and safety guidelines.
3/20/2023 9:21:15 AM •
Miscellaneous
•
22 views • 1 helpful votes
It sounds like there's air coming from the back of the primer bulb when I press in on it. Air bubbles in fuel lines
If you are noticing air bubbles in the fuel lines and hear air coming from the back of the primer bulb when you press it in, it is possible that there is an issue with the fuel system of your engine.
One potential cause of this issue could be a leaking fuel line or a damaged primer bulb. If there is a small hole or crack in the fuel line, air could be entering the system and causing bubbles to form. Similarly, if the primer bulb is damaged or worn out, it may not be able to create a proper seal when pressed, allowing air to enter the system.
Another potential cause could be a clogged fuel filter or a problem with the fuel pump. If the fuel filter is dirty or clogged, it may not be allowing enough fuel to flow through, which could cause air to be drawn into the system. Similarly, if the fuel pump is not functioning properly, it may not be able to pump fuel through the system effectively, which could also cause air to be drawn in.
It is important to address this issue as soon as possible, as air bubbles in the fuel lines can cause the engine to run poorly or even stall. You may want to consider having a professional mechanic diagnose and repair the problem to ensure that it is properly fixed.
3/19/2023 10:31:46 PM •
Miscellaneous
•
22 views • 0 helpful votes
Titan airless paint sprayer is not getting power
If your Titan airless paint sprayer is not getting power, there are a few potential causes that you can check:
- Check the power source: Make sure that the power outlet or extension cord you are using is functioning properly. Plug in a different device to see if the outlet is working. If it is not, try plugging the sprayer into a different outlet.
- Check the power cord: Inspect the power cord for any visible damage or wear, such as cuts or frayed wires. If you find any issues, stop using the sprayer immediately and replace the cord.
- Check the on/off switch: Make sure that the on/off switch on the sprayer is turned on. If it is, try turning it off and then back on again to reset it.
- Check the fuse: There may be a fuse inside the sprayer that has blown, preventing it from getting power. Consult the user manual to locate the fuse and replace it if necessary.
If none of these solutions work, it may be necessary to take the sprayer to a professional repair service for further diagnosis and repair.
3/19/2023 4:26:22 PM •
Miscellaneous
•
22 views • 1 helpful votes
Can't locate the Engine Coolant Temperature Sensor on my 2000 Nissan Sentra SE 20
The Engine Coolant Temperature (ECT) sensor on a 2000 Nissan Sentra SE 2.0L is located on the engine block, near the thermostat housing. Here are the steps to locate the sensor:
1. Locate the thermostat housing: The thermostat housing is located on the engine block, near the top of the engine, and is connected to the upper radiator hose.
2. Look for the ECT sensor: The ECT sensor is usually located near the thermostat housing. Look for a small sensor with a wire harness connected to it. It is typically located on the engine block or cylinder head.
3. Follow the wire harness: If you're having trouble locating the ECT sensor, follow the wire harness from the thermostat housing. The wire harness will lead you to the sensor.
Once you've located the ECT sensor, you can test it using a multimeter to ensure it's functioning properly. If you're unsure about how to proceed, it's recommended to consult with a qualified mechanic or automotive specialist for further assistance.
3/11/2023 7:31:00 PM •
Miscellaneous
•
25 views • 1 helpful votes
Not finding what you are looking for?
