Measuring Tools & Sensors - Recent Questions, Troubleshooting & Support


Try changing batteries and hit reset button?

Equity Time USA... | Answered Yesterday


Might be the wrong plug, too long and hits the piston...
Or your oil is low.
Or your battery is weak... try jumper cables from a car directly on the starter.
Or move the engine by hand just over the compression point, so when you start it has more speed to get past the compression :-)

Briggs Measuring... | Answered on May 13, 2020


Contact LaCrosse direct. We are FIXYA dot com


Wireless Thermometer - La Crosse Technology

www.lacrossetechnology.com > media > catalog > product

PDF This Wireless Thermometer features: indoor/outdoor temperature with MIN/MAX readings in Fahrenheit or Celsius, outdoor temperature trend arrow, and manual ...

Measuring Tools... | Answered on May 07, 2020


NOT BEING A B &D TECH SUPPORT PERSON i CAN ONLY SUGGEST TRYING THEIR WEBSITE

Sonic Black And... | Answered on May 06, 2020


First, insert the new batteries into the Temperature sensor. (see "Install and replace batteries in the Temperature sensor").
2.
Immediately after and within 30 seconds, insert the batteries into Weather station (see "Install
and replace batteries in the Weather station"). Once the batteries are in place, all segments of
the LCD will light up briefly. Following the time as 12:00 and the "Weather man" icon will be
displayed. If these are not displayed after 60 seconds, remove the batteries and wait for at least
10 seconds before reinserting them.
3.
After inserting the batteries, the Weather station will start receiving data from the sensor. The
outdoor temperature and the signal reception icon should then be displayed on the Weather
station. If this does not happen after 3 minutes, the batteries will need to be removed from both
units and reset from step 1.
4.
In order to ensure sufficient 915 MHz transmission however, this should under good conditions
be a distance no more than 100 meters between the final position of the Weather Station and the
sensor (see notes on "Mounting" and "915 MHz Reception").
Note:

If the signal reception is not successful on the first frequency (915MHz) for 45 seconds, the
frequency is changed to 920MHz and the learning is tried another 45 seconds. If still not....

and about the Sad Face

Comfortable:A happy face icon "(68°F to 78.6°F)and relative humidity reading between 45% and 65%.Uncomfortable:A sad face icon " " indicating any value outside the comfortable range

https://www.manualslib.com/manual/516303/La-Crosse-Technology-Ws-9630u-It-Ca.html?page=7#manual

Measuring Tools... | Answered on Apr 29, 2020


Reset display by pressing the RESET button, located on the back of the display unit inside the battery compartment. Date and time will need to be entered after a reset. Flashing of the outdoor temperature is generally an indication of wireless interference.
https://www.acurite.com/media/manuals/00754-instructions.pdf
Hard Reset:
  1. Bring both the sensor and display unit together and power down by removing at least one battery from each and/or removing the power cord.
  2. Make sure the A-B-C switch on both units matches. ...
  3. Reinstall the battery in the outdoor sensor.
  4. Reinstall batteries and/or power cord into the display unit
https://support.acurite.com/hc/en-us/articles/360013641694-3-in-1-Reset

Measuring Tools... | Answered on Apr 29, 2020


My outdoor sensor has a b c options. My indoor does not. What do I set outdoors to?

Acu-Rite... | Answered on Apr 29, 2020


You may use following removals Tools
  • Moving Dollies
  • Pallet jacks
  • Hand Trucks
  • Hydraulic Tools
You may also get information about Removals Tools Here
Removal Companies Tools

Measuring Tools... | Answered on Apr 24, 2020


https://support.acurite.com/hc/en-us/articles/360007555574-Temperature-is-Flashing-Stuck-or-Showing-Dashes-on-a-Basic-Multi-Sensor-Display-

Measuring Tools... | Answered on Apr 22, 2020


Take it apart and get some isopropyl alcohol and a q-tip. check for corrosion around the terminals. If there is none, look for loose connections. If there is something loose, check if a bit of the board is loose. If a bit of the board is stuck to the terminals, give up on batteries.

Measuring Tools... | Answered on Apr 22, 2020


THEY DO NOT WORK WITHOUT COIL WIRE HOOKED UP TO PLUG

Briggs Measuring... | Answered on Apr 22, 2020


First, loosen the arm until it is moving freely. Next, open the throttle to full capacity while making a note of which direction the arm moves in when the throttle moves through it. Once the throttle is fully opened, move the governor shaft in the same direction the governor arm traveled.
https://www.hunker.com/12359232/how-to-adjust-a-briggs-stratton-governor

Briggs &... | Answered on Apr 11, 2020


I do not believe that you can buy these separately. They are factory programmed and paired together.

Measuring Tools... | Answered on Apr 09, 2020


https://www.mitutoyo.com/wp-content/uploads/2016/09/L-section-CMM.pdf

https://www.cmmmanager.com/forum/viewtopic.php?t=1377

Mitutoyo... | Answered on Apr 07, 2020


Open this.
press CTRL+F
type in 'limit'
3 mentions of exceeding limits. A new stylus may be the fix

An alarm warns you when the cumulative measurement distance exceeds a preset limit. This feature can be used to prevent problems that would be caused by worn out styli.Any value can be specified as the limit.

https://www.mitutoyo.com/wp-content/uploads/2015/08/Surftest_SJ210.pdf

and
https://www.mitutoyo.co.jp/eng/support/service/catalog/03/E4388_178.pdf

www.mitutoyo.co.jp > eng > contact > products > sj
We would like to offer you a free copy of our Surftest SJ-210, 310, 411, 412, 500, SV-2100 Communication program, which enables easy use of the ...

Mitutoyo... | Answered on Mar 29, 2020

Not finding what you are looking for?
Measuring Tools & Sensors Logo

11,929 questions posted

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

18330 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

55379 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...