Masonry Tools - Recent Questions, Troubleshooting & Support

0helpful
3answers

How to change blade

I replaced blades on my planer and now the wood is getting chatter on it, why?
7/30/2022 3:42:31 AM • Delta TP300... • Answered on Jul 30, 2022
0helpful
2answers

Blade guard for Atlas 6'' jointer

I can send you pics of the one I made from plywood for this same jointer. If you're looking for an original I can't help you there.
7/15/2022 2:10:16 PM • Masonry Tools • Answered on Jul 15, 2022
0helpful
1answer

Where can I find a cutter head for a sears 6-1/8 jointer planer?

no info generic answer sears.com -----chraftsman.com ------online search using make and model ----stores that carry sears power tools
3/2/2022 1:22:14 PM • Masonry Tools • Answered on Mar 02, 2022
0helpful
2answers

Need a manual for a

If you're still interested, please see this answer and follow the links.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!
2/5/2022 12:03:11 AM • Masonry Tools • Answered on Feb 05, 2022
0helpful
1answer

Where I can buy guage for ryobi 10" thickness planer/AP-10

5/25/2021 9:23:45 PM • Ryobi Masonry... • Answered on May 25, 2021
0helpful
1answer
0helpful
1answer

Tuckpointing brick, mortar won't stay in. have a

is the recess deep enough on the bed and perp joints if so is the mortar the right consistency. a little tip is to wet the joints with water before jointing. it stop the mortar drying out to quick
12/28/2014 7:14:40 PM • Masonry Tools • Answered on Dec 28, 2014
0helpful
1answer

What is the proper way to hold the masonry trowel?

On the website http://www.masonryforlife.comthey explain: "Learning to hold the trowel correctly is important and will make the job easier. Gripping the handle with four fingers and putting the thumb on top of the metal band (ferrule) on the handle is how most masons hold a trowel."
12/17/2014 3:10:17 AM • Masonry Tools • Answered on Dec 17, 2014
0helpful
2answers

1 yard cement is how many cubic feet

kakima is 100% correct, but to add to it so you understand how he got that 27 cubic feet... you can picture a cube. A cubic yard is 3 foot tall x 3 foot wide x 3 foot high. (A cubic foot is 1 foot tall x 1 foot wide x 1 foot high). So 3 x 3 x 3 = 27. 1-yard-cement-many-cubic-feet-qu0oq53oafs2uwkbtfxhnjmj-4-0.jpg
10/30/2014 2:54:01 AM • Masonry Tools • Answered on Oct 30, 2014
0helpful
1answer

Restring clothesline hills

This may assist "I found that Hills don't sell new line kits direct anymore, so I got some poly core line from Mitre 10, 60m for $30. Study how the original line was strung through the clips and how it was tied at each end, and you will find that you have to remove 4 plastic wedges which secure the line in the end caps, these things http://www.breezedryer.com/index.php?p=product&id=792 The wedge is not shown. You just push it out upwards. Then cut away and pull out the old line from all the clips, these things http://www.breezedryer.com/index.php?p=product&id=741 Then tie the line onto one end cap as it was before, and restring the whole hoist. To get the line into the clips, you can carefully lever a bit with a screwdriver. Don't worry too much about tension yet, just leave the line a bit slack on each run. You will have to pass the coil of line over the top of the arms many times. Finally cut it off after the final run, leaving enough line hanging down to secure the arms in a bunch when the hoist is folded up. Make the final knot as it was, and then, without skewing the arms sideways, remove any slack going around and outwards, and finally pull in and tighten the final knot at the outer end, and replace the 4 wedges. The line will stretch, so you may need this final step once more.
9/6/2014 8:02:38 AM • Hills Rotary 8... • Answered on Sep 06, 2014
0helpful
1answer

I have a older style hills fold down line The line

use u clamps to help them they are small and do the job your local hardware will have them
7/29/2014 1:14:50 PM • Hills Rotary 8... • Answered on Jul 29, 2014
0helpful
1answer

Rewiring switch

I do not have a clue as to what you have but a simple switch has two connections and you can connect either way.
7/23/2014 4:09:38 PM • Masonry Tools • Answered on Jul 23, 2014
Not finding what you are looking for?
Masonry Tools Logo

187 questions posted

Ask a Question

Usually answered in minutes!

Top Masonry Tools Experts

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

49993 Answers

Tom Chichester

Level 3 Expert

62329 Answers

ray gallant

Level 3 Expert

74163 Answers

Are you a Masonry Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...