Electrical Supplies - Answered Questions & Fixed Issues

You can ask it from your supplier

Coleman... | Answered 2 days ago | 178 views

If you need to have a diesel generator set in future, please refer to www.dieselgeneratortech.com

Electrical... | Answered 2 days ago | 123 views

If you need to have a diesel generator set in future, please refer to www.dieselgeneratortech.com

Electrical... | Answered 2 days ago | 160 views

Hello, friend, you can check the user manual or ask the supplier who provide the genset to you.

Electrical... | Answered 2 days ago | 18 views

There isn't much you can do with servicing the generator set or transfer switch unless you've got lots of experience in diagnoising semi-conductors and electronic components.

Depending on the age of the system, it would be benificial to have a qualified service tech take a look at it.

As an electrician, I've installed several back up generator sets in homes for customers and have had a few of these automatic transfer switches with intermittent operation issues. Sometimes it's the switch and other times it's the Generator that is causing the problems.

Hope this helps, and best regards!

Generac 100 Amp... | Answered on May 23, 2020 | 644 views

Does your generator is single phase generator set or three phase four wire generator? Why your generator set is 110V at full load, it should be 220V or 240V to generator electricity. If it is used for industrial equipment, it should be 380V, 400V, 440V, etc.
Generator technical support: https://www.dieselgeneratortech.com/support/

Yamaha 2500 Watt... | Answered on May 23, 2020 | 193 views

Connection between ATS and generator:
220V signal line is connected to generator control cabinet terminal (D2 and D3)
ats -undefined-undefined-0.jpg

Generac 100 Amp... | Answered on May 23, 2020 | 239 views

Hi there!
Take a look at pic 2 and pic 6 on this page.
The colors do not matter there is no forced set standard for wiring and colors but we are aware of commonly used color schemes.

Pole 2=Line
Pole 3= High
Pole 4=Low
Ground is Ground
Good Luck!

Electrical... | Answered on May 20, 2020 | 71 views

Check all fuses.

Try the lamp test and make sure all panel lamps light.

Check battery voltage is 12.3VDC or greater.

Coleman... | Answered on May 20, 2020 | 20 views

Make sure the oil is correct and nothingimpedes the cooling.

MotorGuide... | Answered on May 19, 2020 | 93 views


Kipor Electrical... | Answered on May 14, 2020 | 21 views

Removing a circuit breaker from your home's electrical service panel is an easy job that takes just a few minutes. However, it's not a suitable project for homeowners who are unfamiliar with electrical systems. The service panel is where the utility's power comes into your house, and portions of it carry deadly levels of electricity at all times. Removing the panel cover exposes the live elements, so you must be very careful not to touch them.

  1. Turn Off the Main Breaker. Make sure the ground or floor and the electrical service panel are completely dry. ...
  2. Unscrew the Panel Cover. ...
  3. Remove the Cover. ...
  4. Test for Power. ...
  5. Turn Off the Branch Breaker. ...
  6. Rock the Breaker Back. ...
  7. Pull the Breaker Out. ...
  8. Unscrew the Breaker Wire.

Electrical... | Answered on May 13, 2020 | 22 views

Make sure it gets gas; replace spark plug and apply chocke.

Subaru... | Answered on May 13, 2020 | 44 views

The load it too high for the gennie or the breaker is getting warn or is already warm from sitting in the sun.

Electrical... | Answered on May 13, 2020 | 59 views

Do normal maintenance first, like oil, oil filter and air filter and then let it firts warm up before applying a load.

Electrical... | Answered on May 13, 2020 | 43 views

Not finding what you are looking for?
Electrical Supplies Logo

Ask a Question

Usually answered in minutes!

Top Electrical Supplies Experts

Gene Haynes

Level 3 Expert

5391 Answers


Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18330 Answers

Are you an Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides