Dryers - Page 7 - Recent Questions, Troubleshooting & Support

This must be a common problem, since I Googled the part number and it popped up before I completed the number. I am going to have to order a new remote, since I don't have a solder pen. Wish me luck.

You will most likely need to replace the receiver with a new one from hunter. The receiver is actually a complete controller and contains the receiver, relays (which you hear clicking) and starting condensors(large capacitors which hold a charge that is "dumped" over the windings to get the motor to start from a dead stop). These appear to be pretty tightly assembled unless you have a desire to start replacing parts "off the board."

E89

I have this problem with my Hoover VHC681C. The plastic at the back of the condenser unit warps outwards and stops it fitting back in the hole. To work around the problem, when I've finished washing out the condenser I pour very hot water on the warped plastic to soften it, push it back into shape with a wooden spoon handle and hold it there while it cools. Then I hold it into shape with my fingers before slamming the condenser back into the hole. You have to be quick! A replacement condenser is £70 - £100 in the UK. Very disappointed in this machine. I will consider shaving off the warped plastic if it becomes too troublesome.

Make and model may help you get an answer.

They always screech when the belt slips. There are usually only 2 reasons this happens. The drum slides at the lower front are worn out and creating too much friction. Or The rear drum bearing has worn out, and again too much friction. ..

https://search.yahoo.com/search?fr=mcafee&type=E210US1494G0&p=kenmore+dryer+will+not+start

They all work to a theme so check out the videos.

I have a 52" Casa Vieja® Probe II™ Ceiling Fan and need to

JustAnswer https://www.justanswer.com > home-improvement > 4... Dec 16, 2010 - I have a 52" Casa Vieja® Probe II™ Ceiling Fan and need to replace the light. How do I remove the cover to get to the light? 1 answer · Top answer: Hello, and thanks for your question! The hooks that she talked about are a ..

Hi Eunice, Is this the Hampton Bay Barrow 52 inch ceiling fan? Just wondering if the model number you provided is this fan or not https://hampton-lighting.com/hampton-bay-barrow-island-ceiling-fan/ Regards,

They appear to be lumped together on the Manualzz site. My search query is modified to only show model 47300. https://www.google.com/search?q=Hunter+thermostat+%2247300%22+manual ..

their are 3 models for rid do online search for info for distributors service manuals etc -----https://www.nationalpowersports.net/itemdetails?itemid=50058 ---

Follow these simple steps:

1. Turn on the dryer by pressing the "Power" or "Start" button.
2. Use the "Time Dry" or "Timed Dry" button to select the desired drying time. Press it repeatedly to increase the time in one-minute increments or hold it down to scroll through the time options more quickly.
3. Once you've set the desired drying time, press the "Start" button to begin the drying cycle with the new time settings.

There is one available here

Whirlpool 8544945 Part Number : Knob, Timer (Silver)

Unlimited Appliance Parts https://www.unlimitedapplianceparts.com > 8544945-... KNOB ASM - DELTA/HD, WPL. US$28.81 All the rest say discontinued. https://www.google.com/search?q=WPL-8544945 ..

possible bad motor

Your Kenmore Dryer has a number of things that can cause this. Most basic, the house breaker has tripped. The timer or electronic mainboard has failed. The element has failed One of the 3 heat regulation devices has failed or tripped out, one resets itself, the thermal fuse has to be replaced. 'make model (what it is)' in all questions please. ..

Hi Jolene...You could have numerous problems causing your dryer not to heat.
I included some things to try and locate the problem part.
You can buy the parts needed on the following websites or numerous other website that sell parts.
http://www.partselect.com/
http://www.appliancepartspros.com/index.aspx


ALWAYS UNPLUG YOUR DRYER BEFORE ATTEMPTING TO DO ANY WORK ON IT.
Check to make sure you are getting full 220 Volt power to the dryer, if you are then:
Check your Wiring
Often the main wiring connection from the house, at the dryer, burns and the connection breaks.
If this has happened to your dryer, you need to replace the power cord and the terminal block inside the dryer to which the
wire is attached.
Check the Door Switch
If the door switch or the door-switch actuator is defective, the dryer won't work and you need to replace the failed
component. The switch is inside the dryer main housing near the door frame.
Sometimes you need to raise or open the top or front of the dryer to reach the switch.
Check for continuity you should have none with door open, and should have a reading when closed.
If not replace the door switch.
Check to make sure you heating problem is not a lint build up in the discharge hose or the dryer,as this condition can cause
heater/thermistor problems such as overheating of the heating coil leading to failure of the coil and burnout of the
thermostat/thermistor due to overheat.
Remove the back/or front just under the door of the machine and try to locate the air duct going from the blower to the drum. Normally inside/outside the air duct you will find the heating coil and the thermostats/thermistors. Once you have located the heating coil, remove the two wires from it and check the coil with an ohm meter across the two terminals of the coil.
You should read continuity across the terminals, if not you will need to replace the coil as it is faulty.
If the heating coil is ok, then:
You can check the thermostat/thermistor one at a time by removing the two wires and taping them together with electrical tape
or with an ohm meter to test the thermostat/thermistor. (Should have/show continuity)
If the coil heats up then replace the thermostat/thermistor.
(Thermal fuse.If it overheats the dryer will not operate. It's located on the blower housing. It cannot be reset. A vent clogged
with lint can cause it to overheat. You can test it with an Ohm meter or continuity checker, if no continuity, replace it)
DO NOT LEAVE THE WIRES TAPED TOGETHER AFTER THE TEST.
This could cause a FIRE, as you have removed the safety of overheat from the machine.
Right after replacing a dryer element, always run the dryer on 'air fluff' / 'no heat', and go outside to verify there's
plenty of air coming out your vent system.
If the vent's clogged, that new element can burn out very quickly.
For video and pictures on how to replace an element go to the following website:
davesrepair.com/DIYhelp/DIYreplacingWPLdryels.htm

This is a FREE answer, Please rate me...Hunter

The air flow problem is not the machine. There is probably a clog in the venting system in the house that needs to be cleaned out. When is the last time that was done?