Breville Logo

Breville Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 518 Products
  • 3K Answers

Time for a new one as it will be too expensive to have it repaired.

Breville Kitchen... | Answered on Jun 25, 2020

I had the same problem. I opened up the toaster and found that the electromagnet that holds the plastic clip to keep the toaster down had a tiny crumb between the magnet and the metal plate. I cleaned the magnet and it is working fine again. We spent 6 months burning toast by holding it down with a chopstick wedged between the lever and finally took a shot before I went to buy a new one. Took me all of 15 minutes.

Breville CT20... | Answered on Jun 04, 2020

I fixed my juicer that had this problem, the problem was the thermal fuse which is located directly on the motor with some plastic covering it. You can replace the fuse or do what I did and just cut off the fuse and attach the two wires together (no more fuse) and my machine now works again :)

Breville Juicers | Answered on May 25, 2020

anon.nick-20625 was right.

Opened the bottom of the kettle, not the charging base, using the three odd screws.

Found the white trip switch, which was a white line in the socket which connects the kettle to the charging base. Pressed it with a screwdriver and it came out more. Tested the kettle, works!


Breville "Ikon"... | Answered on Mar 29, 2020

I found the answer (see below) posted on another web site. I followed the instructions and replaced the spring. I found, as the original poster had, that the new spring works better than the original and is much more sturdy. To the original instructions, I would add the following:

1) There are about 20 screws so have patience removing and replacing the screws.
2) Step 3, "Slide off the rear panel" requires further clarification as the panel will not slide off even with all screws removed. I had to turn the oven over, with the top of the oven sitting on the work table. I then used a screw driver to lift the two tabs that hold the back panel to the bottom panel. With the tabs lifted, the back panel will rotate away from the oven along the edge where back panel slides into the top panel. The back panel can then be slid out. I have included three photos that show this step.
3) Step 7, "Re-attach feet": Be sure to use the guides on the bottom of the oven to slide the foot assembly onto the oven. I had unsuccessfully tried to screw the feet onto the oven without using the guides.

Oringinal instructions for replacing the broken spring:

Just repaired this yesterday.

Got a spring from Lowes (Hillman Part # 543028 for about $4), it's larger than the original but seems much sturdier, original is really thin metal. Fit the space provided without problem.

Oddly, end result was a more 'giving' spring action, prefer it to original, which loved to snap shut unless door was 100% opened (ie fully 90 degree open).

This is for BOV800XL:
1. Remove all rear screws
2. Remove feet entirely
3. Slide off rear panel
4. I was not able to remove top housing - but I was able to gently pry sides open just enough to thread the new spring with a little ingenuity and effort. Watch out for sharp metal edges everywhere.
5. Slide back in (remember that top edge goes under the top edge/lip)
6. Put all screws back in
7. Re-attach feet

Good luck!

7a505b80-f785-4973-b674-12594d9dcb1d.jpg 2e67ee3d-99c9-4e88-8b9f-8d1721e5caa6.jpg 529808f4-8d72-4aea-8286-b525347addee.jpg

Breville... | Answered on Mar 13, 2020

Good day To you Boss!!!

Because you are my boss you had all the right not to pay for me If you did not found what you are looking for to resolve your problem because to help you is my primary mission.

Please click the links below for the manual and information how to remove and clean your Breville Juicer, just please be patient..

Please don't forget to rate and have testimonial if your problem got solve with my solutions..I hope your problem got solve...

Thank you!!!

Breville 800JEXL... | Answered on Mar 11, 2020

We heard directly from Breville that these toasters are DESIGNED to do this! Ours toasted very unevenly for a month and then stopped toasting on one side all together.... Breville says too bad; it's designed to work like a "restaurant" toaster -- which is apparently one side only. We told them that it used to work somewhat, but now one side doesn't work at all. They said that we are mistaken -- that it never toasted both sides. Can you imagine? Unbelievable.

Breville Kitchen... | Answered on Nov 21, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Breville Experts

ray gallant

Level 3 Expert

68313 Answers

Tom Chichester

Level 3 Expert

55627 Answers

Bill Boyd

Level 3 Expert

53812 Answers

Are you a Breville Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides