Bowflex Exercise & Fitness - Recent Questions, Troubleshooting & Support

I was having the same issue to a T. I called Bowflex tech support, they told me that without a doubt the main pc board that is under the treads needed to be replaced for $515. I then trouble shot myself and got it up and running in minutes for $0. Take of the plastic top from the pc board area, unplug the little clipped in 2 wire plug labelled Fan. It litterally says fan on the board and you can see 2 wires going right to the fan. Once that is disconnected try to Quick Start. It should work. You can either replace the little fan for $6 @ radio shack or run a fan your self simply by facing your own in the same area. Most people are running a fan for themselves anyway, just aim for both. Good luck.

Error code 0AB on a Fisher & Paykel refrigerator may indicate a problem with the evaporator temperature sensor. The evaporator temperature sensor is responsible for monitoring the temperature inside the freezer compartment. If the sensor is not functioning properly, it may send incorrect temperature readings to the control board, causing the error code to appear. Some possible causes of this error code include:

• The evaporator temperature sensor is malfunctioning and needs to be replaced.
• The wiring connections between the sensor and the control board are loose or damaged.
• The control board itself is malfunctioning.

If you are seeing this error code, I would recommend checking the wiring connections and the sensor and if they are ok then the control board may need to be replaced. It is best to contact a qualified technician or the manufacturer for help troubleshooting and repairing the issue, as working on refrigeration equipment can be dangerous if you are not properly trained and equipped.

remove and replace console bezel assembly.

The motor must move the drive pulley for calibration to pass. remove rear covers and check drive belt. you should hear the lwr board relay click to engage the motor. if you hear it and the motor does not move and you have checked the belt then you need to test the motor. Typically remove the belt and turn by hand...it should be very smooth and spin freely. If not replace the motor. Direct 9 volts to the motor leads unplugged from the board will tell you if the motor is good. be careful as capacitors are present and risk of shock is always possible. capacitors stay charged for about 10 mins after unit is unplugged

Step 1:

see the comment. and fix it. Run the software calibration."SAFETY SHUTDOWN Loss of Speed Signal" or "L5" WITH NO belt movementThe speed sensor is not recognizing any motor movement. This displays the error message to the upper board. Refer to the proper flowchart.

Step 2:

The Steps for Newer Style Console Calibration:

1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

10. Press ENTER. You should see "SS" or "55" in the console.

11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

manual download

The machine needs to be re-callibrated. L5 error.
Your speed sensor must have been damaged either during shipping or use. You'll need a new one. If under warranty - give Bowflex a call. They will ship you out a new sensor and guide you through installing it via the phone... re-calibrating the machine... and getting it operational again. It will take about 2 hours.

The instruction book doesn't mention calibration. be sure to not callibrate in metrics, however (there's no way to easily tell the difference - you have to ask) or you'll be strolling like a walk in the park at 5 "mph".

Thanks for using FixY - a FixYa rating is appreciated!!

contact Bowflex this is not bowflex tech support

Some things to try: 1. make sure the safety key is plugged in 2. make sure you can move the belts by hand, that nothing is seized up 3. make sure the i/o cables running from the console, through the upright, and back to the control board, are all connected together securely and have not been damaged. 4. make sure the red and black motor wires are connected to the the control board.

https://www.fixya.com/support/t2438337-bowflex_treadclimber_calibration_failed https://www.manualslib.com/manual/612664/Bowflex-Treadclimber-1000.html?page=34 https://manualzz.com/doc/871362/bowflex-treadclimber-1000-service-manual

It appears to be a known issue. Contact them direct. http://pdfstream.manualsonline.com/f/fa628352-5d53-48e6-beac-ff49402d2ece.pdf ..

Hi, i want to purchase a treadmill but i am new to this exercising machine. I saw some top rated products listed here https://consumerhome.org/best-treadmill-under-1000/ which i'll be glad if anyone can go through for a suggestion

If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

The hydraulic shocks found on exercise machines aren't very different to the shocks found on cars, bikes and trucks or even inside some washing machines - the ones on display on bikes and exercise machines are better finished and nicer to look at. Your question is asked everyday by thousands of vehicle owners who also want to know why shocks leak. I have a theory, but it is just a theory - If a telescopic shock absorber is going to leak they mostly start leaking while relatively young. I think very few leak because the seal is worn out - a very few do and that happens after a long service life. I think in some cases it could be the quality of the seal or the way it is fitted but my theory is about the ambient temperature, the temperature of the components and the temperature of the oil that fills the shock. It is possible during manufacture a certain volume (rather than a weight) of oil is placed in each shock and at certain times, such as first thing after the weekend, in the winter perhaps, the oil will be cold so when the finished item meets hot weather the fluid expands and the level could rise enough to overwhelm the seal...

www.treadmillpartszone.com You must locate to side from the power switch you must find the fuse holder and replace the fuse with THE SAME SIZE+CAPACITY+VOLTAGE INDICATED FROM THE SAME FUSE. Remember if the fuse is Blown again or continuing you have a short circuite in a) Transformer b) Main Motor c) Main Controller Board d) Faulty ground in your receptacel from the wall very carefully. attached the block diagram that I did for to illustrate to person like you, good luck. sincerely.

Hi. Please click on the link to view how to calibrate the treadmill. https://www.manualsdir.com/manuals/58333/bowflex-treadclimber-5000-treadclimber-3000-treadclimber-1000.html?page=33 Kind regards.

Bowflex company is alive and kicking, did you try calling them for the best information? Don't let them try to sell you a new machine unless they give you a great big discount, ask about repair.

I think I have 4 boards in total. They all give me error code h30. Do yourself a favour and don’t buy a bowflex treadclimber.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. Check for treadmill articles http://electro-medical.blogspot.com/

you should be able to then by turning the caps on the top of them