Bosch Kitchen Ranges - Recent Questions, Troubleshooting & Support


Near your Burner will likely be a metal heater that glows RED HOT next to the gas burner and when the heat is detected the gas is let go to light. A Safety and a way to light the gas. If you look it may glow slightly but needs to glow full bore to light. This is the most common failure. If you get a kit that has Wire Nuts be sure they are Ceramic Wire Nuts due to the heat or the plastic ones will melt off exposing the wires. Good Luck.

Bosch Kitchen... • Answered on Nov 18, 2019


Use digital tester 1st test the power outlet if theres a voltageif OK check the power cord if broken if OK check the fuse using continuity test/setting,

Bosch Kitchen... • Answered on Jul 15, 2019


Don't fiddle with gas - get a technician or increase your fire insurance.

Bosch Kitchen... • Answered on Jan 20, 2019


set oven into self clean wait till it says door locked and on and then cancel cycle after a couple min should unlock if not you may need lock there is no safty latch ther is door removal latch on hinges if these were in hold position the door would not close

Bosch Kitchen... • Answered on Jan 20, 2019


Error 111 means that your oven thinks that it's over heating. Now whether or not the oven is actually overheating or not, this can be caused by either a bad oven sensor or a bad display relay control board. You can't test the board but you can test the sensor. Open the door and remove the 3-4" long thin metal rod attached to the back wall. There are 2 screws holding the sensor on that you can remove and then pull the sensor forward until you can disconnect it. With a multimeter, check the resistance of the sensor at room temperature and it should be about 1080 ohms. If it's not, replace the sensor, otherwise you need to replace your relay board.

Bosch Kitchen... • Answered on Nov 22, 2018


Most ovens have two or more heater elements, have them checked out one could be faulty.

Bosch Kitchen... • Answered on Oct 01, 2018


TURN OFF POWER pull knobs and dials off open oven door look under console remove toex screws in lower console(control panel) the front panel glass will drop out you can know see a metal panel that surface switchs mount too the screws that hold panel are around the edge the screws that hold cooktop down should be able to be seen you do not have to remove the cooktop to replace switches but once the front screws for cooktop are removed the top slides forward and lifts off there will be 1 ground wiire to disconect from cooktop if you do put it back gl

Bosch Kitchen... • Answered on Sep 21, 2018


First unplug your microwave. I will assume you know how to take apart a microwave oven. There are plastic screws on the inside of the door that need to be completely unscrewed, then the outer glass door will lift up and off. After this it is easier to unscrew the door hinges. 00441202

Bosch Kitchen... • Answered on Mar 23, 2018


Check the back side of the woofer. they are frequently designed with protection fuses to prevent failure.

Bosch Kitchen... • Answered on Mar 07, 2018


there is a repair kit comes with hinges liner heat shield call bosch with mod and ser # they may cover

Bosch Integra... • Answered on Feb 05, 2018


EN Control buttons separating from control mounting bracket. Affected Countries CA, US Affected Appliances HPCN36NS/01, HPCB36NS/01, HPCN48NS/01, HPCB48NS/01 Fault description / Customers complaint / Diagnostic Codes Diagnostic Codes (DC) The following table contains the diagnostic codes, which most commonly occur in connection with the mentioned fault description. Depending on the actual information from the customer, other diagnostic codes are possible. DC Fault description of the customer 160100X45000 Mechanical damage / Holder Root cause On some Thermador Professional hoods with FD 9407 to 9611, the control buttons may separate from the control mounting bracket due to insufficient adhesive between the control mounting bracket and the inside of the hood canopy. Solution Beginning with FD 9612, wider tape was implemented in production. For units built prior to that time, service kit 12022532 is available. The new repair kit includes the control-mounting bracket with wider tape affixed to it, and four screws. The tape will provide more surface coverage to improve the support of the mounting bracket.

Bosch DKE93xxUC... • Answered on Jan 02, 2018

Not finding what you are looking for?
Bosch Logo

491 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6259 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Are you a Bosch Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...