Belling Kitchen Ranges - Recent Questions, Troubleshooting & Support

0helpful
1answer

Belling kensington 100E Range Cooker. How do I access the control panel please.

Question edited for clarity. Question moved from Kensington Computer category to Belling Kitchen Ranges. 'Access' in "how do I unlock it and press the buttons", or "how do I take is apart"? There is some help in the link, or reach out to Belling Customer Care. https://www.google.com/search?q=Belling+kensington+100e%2C+access+control+panel ..
11/30/2021 5:11:27 PM • Belling Kitchen... • Answered on Nov 30, 2021
0helpful
2answers

Belling G755 Cooker oven wont stay lit

I'll give this a go! With a cooker like this, you depress and then turn the control knob, press the ignition button and continue to depress the control knob for a few seconds. This is because a device called a thermocouple is heated by the flame and you have to continue to depress the control knob so that sufficient gas flows to heat up the thermocouple. If the thermocouple does not get hot or stay hot then the gas valve is automatically closed - stopping the gas. The thermocouple is a 'flame failure' safety device. If the gas gets cut off then the flame goes out and the thermocouple goes cold switching off the gas valve automatically. However, you are having to try and manually keep the gas going for a good five minutes. I would think that there is either a problem with the thermocouple or the gas control valve! Tony www.birminghamelectricsltd.com
7/30/2021 1:17:14 PM • Belling... • Answered on Jul 30, 2021
0helpful
1answer

I've got a Belling LPG gas oven and it lights ok but then pops and blows itself out. I've replaced the thermocouple and it's made no difference. Any suggestions ?

Taking a guess, I would expect gas is leaking from somewhere and bypassing the burner and when it has built enough to reach the flame it will pop. LPG is heavier than air... I suggest you remove the burner and ensure everything is clean including inside the mixing chamber is free of fluff and dust and ensure the gas jet and gas supply to the jet housing is tight and the connection to the pilot light is similarly tight.
12/5/2020 3:30:46 PM • Belling Kitchen... • Answered on Dec 05, 2020
0helpful
1answer

Belling range electric cooker 60a both ovens are working but the top plates don’t work at all is they a thermal cutout on them or fuse where is that located seems like no power going to the job plates at all Thanks All Thanks all

if diy. turn off power, remove plug from socket. remove access plate or back where cable enters and observe internals . Ascertain if there is are fuses were cable attaches. if nine leave and contact electrical repairs or supplier. remember if you remove or undue screws, you void any guarantee remaining.
10/31/2018 8:35:18 AM • Belling Kitchen... • Answered on Oct 31, 2018
0answers
0helpful
1answer

I have an old belling farmhouse cooker the hob works fine but the oven isn't igniting manually or by the electric ignition The timer is manual and is stuck on the red patch I can't seem to shift it

, push in and turn the control knob to the full on position (large flame symbol). If your hob has an ignition switch on the facia, press it in until your burner lights. • Hold the control knob in for 15 seconds then release. If the burner fails to light within this time, release the control knob and wait one minute before attempting to re-ignite. or Push in the control knob and after a couple of seconds press the ignition switch. • Hold the control knob in for 15 seconds then turn to desired heat, If the burner fails to light within this time, release the control knob and wait one minute before attempting to re-ignite.
2/3/2018 5:34:19 AM • Belling... • Answered on Feb 03, 2018
0helpful
1answer

Have a Belling GT755 and

The oven has a flame detection installed that makes sure the gas turns off if the flame goes out. There are two component that do this. One is the flame detector and the other is the control device that turns the gas off,. Either one of these cold be faulty. The cheapest way is probably to replace the detector in the oven and if that does not work, replace the gas control device.
1/3/2018 9:54:45 AM • Belling... • Answered on Jan 03, 2018
0answers
0answers
0answers
Not finding what you are looking for?
Belling Logo

366 questions posted

Ask a Question

Usually answered in minutes!

Top Belling Kitchen Ranges Experts

Paul Carew

Level 3 Expert

3699 Answers

Vernon Taylor

Level 3 Expert

7446 Answers

Brad Brown

Level 3 Expert

18856 Answers

Are you a Belling Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...