Behringer Audio Players & Recorders - Recent Questions, Troubleshooting & Support

Unfortunately, the Behringer Xenyx x2442usb only comes with a stereo USB interface. The documentation is a bit misleading, but you can only record two channels through the USB interface - the main mix L and R. If you need to record more inputs than that, you'll have to do them separately.

Behringer XENYX... | Answered on Jul 07, 2020

Hmmmmm. Are we talking about your internal or external fuses; Do they blow at the moment you put power on it, and what about the switch of the used voltage ?.... And was it straight away , since when you bought them; Then just send them back, Second hand?, too bad, you're ripped off .

Behringer... | Answered on Oct 13, 2019

I doubt that there is a problem with the unit. Usually people have problems with their cables or the speakon plugs themselves.
Unscrew the connector that is used on both ends and double-check their connections. Sometimes the screws that hold the heavy gauge wire in place, come loose. Also make sure that they are in the right places. Sometimes you have 4 connections. Make sure they are in +1 and -1 connections. Every once in a while you'll find a quirk unit that requires you to use +2 and -2 instead. Look at the back of the amp. It should tell you which numbers it uses. Make sure you check the same thing on the speaker end also. If you have a meter or continuity checker, use it to make sure it's wired right.
This is a professional piece of equipment. They don't go bad easily. Make sure you tighten those connections real good and that you pay close attention to the engraved numbers on the speakon connectors. (That is if they are quality connectors. The cheap ones may NOT tell you the numbering or the phase, ((+ or -)). Hint: The negative one is always closest to the outside of the plug. You'll have to study it to understand that. The screw terminals on the inside have 'walls' on both sides of it. Those are the + connections.
Also, check the switches on the front. You may have one of the switches in the wrong position or setting. Also if you're using phantom powered mics, you have to turn the phantom power on or else they will not work. Hope this helps.

Behringer Audio... | Answered on Oct 05, 2019

The problem is not bad transistor.
the problem is dirt, try to clean dirt in the internal of the amplifier especially the front section that has a foam attached to it.
this should be done by removing the cover of the amplifier.
Also do not overload the amplifier, check its ampere, watt and ohms to ensure balance of the amplifier and the speaker....

Behringer... | Answered on Sep 25, 2019

Sorry I can't answer you're question I don't know but I can say that I am really pleased with it I have gigged it a lot since I bought it and it does not even get very warm after about three hours it I am very pleased with it a good buy for me.

Behringer... | Answered on Jul 01, 2019

Do you have the mics and dongle system accessories? Your question does not state if you have them or not. If you do have these accessories, and you only want to use the wired option, remove the dongle so it stops searching for the microphones.

Hope this helps.

Behringer Audio... | Answered on Jun 27, 2019

Contact Behringer directly with your request.

Behringer Audio... | Answered on Jun 04, 2019

Hello Doug, obviously for what you are saying, you would have a problem in the effects processor of your Behringer, I suggest you use an external processor to corroborate that the problem is not in the shipping bar, or in the allocation of returns
If you have technical knowledge, disarm the mixer and control the internal connections of the effects processor, see if there are no loose solders
I sent you the link to download the circuits of your PMP5000
If you do not find the origin of the fault, look for a specialized technical service
I hope you can solve the problem
Greetings Franco Dosil

Hola Doug, evidentemente por lo que comentas, tendr?as un problema en el procesador de efectos de tu Behringer, te sugiero que utilices un procesador externo para corroborar que el problema no esta en la barra de env?os, ni en la asignaci?n de retornos
Si tienes conocimientos t?cnicos, desarma el mixer y controla las conexiones internad del procesador de efectos, observa si no tiene soldaduras flojas
Te env?o el link para descargar los circuitos de tu PMP5000
Sino encuentras el origen de la falla, busca un servicio t?cnico especializado
Espero puedas resolver el problema
Saludos Franco Dosil

Behringer Audio... | Answered on Apr 30, 2019

Try asking these people:

Behringer Audio... | Answered on Apr 23, 2019

Hi Malcolm, you can connect the compiler to the equalizer input and the equalizer output to the input you use in the Behringer X2222 mixer

Hola Malcolm, puedes conectar la compuatadora a la entrada del ecualizador y la salida del ecualizador a la entrada que usas en el mixer Behringer X2222

Behringer... | Answered on Apr 15, 2019

All is Behringer gear except one 2500w qsc amp. ??????

Behringer Audio... | Answered on Apr 15, 2019

Hello Rico, I pass the link diagrams of the Behringer MX4224

Hola Rico, te paso el link de los diagramas de la Behringer MX4224

Behringer Audio... | Answered on Apr 15, 2019

Cheapest way to try and fix is, with the unit off, turn the crackling control back and forth many times. Wiper sometimes removes corrosion on the carbon strip. If this doesnt work take the knob off and dribble some deoxit d5 down the shaft and work it some more.

Behringer Audio... | Answered on Apr 15, 2019

Not finding what you are looking for?
Behringer Logo

773 questions posted

Ask a Question

Usually answered in minutes!

Top Behringer Audio Players & Recorders Experts


Level 3 Expert

5700 Answers

Rob Beech

Level 2 Expert

63 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers

Are you a Behringer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides