Asko Logo

Asko Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 140 Products
  • 3K Answers
  • 277K Views

Unsure if your model has a front housing to be checked.

http://www.appliancehelponline.com/asko.html

Asko

Dryer Failure Code Condition Check/Repair F1 Condensate drain overfilling Check condensate reservoir pump and drain tube. F2 Maximum drying time exceeded (3hrs) - Check for tripped circuit breaker or blown fuse
- Check ductwork for lint build-up
- Check hi-limit and cycling thermostat
- Check heating element F3 Thermistor fault - Open thermistor, replace
- Bad wiring to thermistor F4 Too much lint in the lint filter, front housing, or in the condenser Clean lint from lint filter and/or condenser F5 Fault in the moisture sensor - Lint covering sensor in front of housing
- Bad sensor
- Bad wiring to sensor

Asko Dryers | Answered Yesterday


this could be the anti flood device has operated in the base of the machine. This is a polystyrene disc that is attatched to a microswitch. If there is water in the base of the machine this disc floats and turns on the pump

Asko 24 in.... | Answered on Jan 28, 2020


I am in Australia so my comment relates to that OZ power supply. The first thing I’d do would be to check the pump to eliminate it as the problem. To do that I’d disconnect at the supply end of the pump’s electric cable and make up a 3 pin plug patch lead and supply power to the pump directly through an RCD protected outlet, and see if the pump works independently of the control board. That would confirm the pump is ok and not going to earth (which would trip the RCD.)
Do the water inlet solenoids come off that board? Because if they are, and are mains voltage, check them the same way. Check everything that comes off that board at the appropriate voltage independently.
There will be temp and water flow and drum-wobble sensors which will be low voltage and all need to be independently checked at the right voltage for each to eliminate them as the problem.
A digital multimeter checking the sensors probably won’t do any damage (blow them up).
Visually check the board visually for any burnt or blown components. Some boards have a thermal fuse in the circuit.
Asko should be able to supply the circuit for the board and it’s values. NZ Govt has legislation that compels Asko to provide this info. We got a new board from Asko NZ by post.

Asko W6441 Front... | Answered on Jan 06, 2020


https://www.repairclinic.com

Asko Washing... | Answered on Dec 08, 2019


The drawer is flushed at some point in the wash cycle to remove powdered detergent residue.

Asko Washing... | Answered on Nov 27, 2019


When the pump runs continuerly it is probably water in the bottom of the dishwasher, when you drag it out on the floor you can try to flip it to see if any water will run out of the mashine, or you an take the bottom front of to see if you can see any water, there should be a water float in the bottom that is being activatet by the water that can leak from the washing cabinet to the bottom of the dishwasher.

Asko Dishwashers | Answered on Oct 22, 2019


Text and videos here

Manual also mentions it
https://www.manualslib.com/manual/785720/Asko-T700-Series.html?page=31

https://www.google.com/search?q=change+the+belt+o+a+t700+drayer+asko&rlz=1C1QJDB_enCA643CA644&oq=change+the+belt+o+a+t700+drayer+asko

Asko Dryers | Answered on Oct 20, 2019


Apparently it is as much as a 16 year old model, and I could not locate instructions for that model, using https www.google.com.

There was a site with parts, however, but not a manual.

A similar model manual, for W6021, shows controls that may be similar.

https://www.manualslib.com/manual/396407/Asko-W6021.html

Asko Washing... | Answered on Oct 12, 2019


I don't know but dryers generally are of a fairly crude construction designed to be cheaply assembled by the manufacturer and not so easy to repair.

The ones I have tackled, the belt replacement entailed removing screws until something important fell off and then on and on until the back of the cabinet could be separated from the front far enough to change the belt...

Asko Dryers | Answered on Oct 11, 2019


It is likely that the timer is stuck and will have to be replaced.

Asko Washing... | Answered on Sep 18, 2019


You will get a good idea here
https://www.youtube.com/results?search_query=asko+t741+replace+dryer+belt+replacement

Asko Dryers | Answered on Sep 13, 2019


It could be a faulty water inlet valve, but it could also be a blocked tube between the tub, and the water level pressure switch, because over time, this can become blocked, and affect how much water enters the machine.
An easy test is to put the machine on a fill cycle and then turn of the mains power to the machine as the machine begins to fill; if the machine continues to fill, it is probably the water valve; if not, check the tube from the tub to the pressure switch.
I hope this helps?

Asko Washing... | Answered on Sep 10, 2019


has the garbage disposal been replaced recently?
- check that the drain plug on disposal s popped out
https://www.hometips.com/wp-content/uploads/2012/05/remove-dishwasher-plug.jpg

-
check that the drain line has a loop in it, i prefer the high drain loop.
http://jbch.us/uploads/3/4/3/0/34305337/dwhighloop1500_orig.jpg

Asko Dishwashers | Answered on Sep 06, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Asko Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Lollo Pop

Level 2 Expert

134 Answers

Brad Brown

Level 3 Expert

18166 Answers

Are you an Asko Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...