APC Logo

APC Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 1K Products
  • 3K Answers
  • 331K Views

Hi,

Most of this 2cycle engines uses any or a combination of the following wiring:
1. engine off is a wire from the CDI that needs to be grounded. The opposite therefore is to unground to allow the engine to run;
2. IGN on, when switched to ON, there is a +12VDC supplied to this wire; and/or
3. START, momentary +12VDC supplied to this wire that goes to the starter relay which then supplies the high current/big wire to the starter motor.

Due to inconsistency of Taiwan/China manufacturers, color coding of the wires is sometimes not standardized and therefore would require that you "wing" it using a DVM.

Hope this be of some help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

APC Miniview... • Answered on Mar 26, 2021


This unit needs at least 120 volts DC to start. I'm thinking yo u might have bad batteries

APC Symmetra PX... • Answered on Nov 22, 2020


Hi Ewiesemann,The amber light on the UPS usually means that the unit is 'on battery' -- meaning that input power is affected. Check to make sure that unit is plugged in and check to make sure that a breaker on a panel feeding the UPS power hasn't tripped.Hope this helps.

APC - UPS -... • Answered on Nov 09, 2020


Dear If UPS working on MAINs but just not wakeup on MAINs then only 3 capasitors need to change.. for further you can diractelly contact @ [email protected]

APC Computers &... • Answered on Nov 09, 2020


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Slide the battery compartment cover off (front bottom cover).
Pull the battery connector connecting the battery to the UPS
Grasp the top and gently pull the battery out of the UPS.


APC Back-UPS RS... • Answered on Oct 03, 2019


most need a battery , the #1 failure , for sure. and fuses. all. (means breaker too, feed and in unit) RTM yet at APC, they have manual and find 2000 that is what all techs do, as no 2 UPS are the same, so.........

APC Computers &... • Answered on Sep 24, 2019


Best thing about this new service is that you are HELP NUMBER +1 833 272 0777never placed on hold and get to talk to real repairmen in the US.

APC Computers &... • Answered on Mar 21, 2019


A UPS, it is. with battery. 2 new batteries fit in side, or it is 1 battery model and tried 1 battery new and then the next? so all this is about a beeper too loud. well with the line cord remove and battery out, find the sonic beeper and see that hole there. stuff chewing bump in that hole. ends that. remove it. tape it or stuff gum ./clay or even rtv caulk in the hole to make it more quiet or zero sounds. they do not let you change the threshold of the battery low warning, if you do that that wrecks the battery if too deeply discharge, (its lead acid gell cell and $20 every time you wreck it)

APC Computers &... • Answered on Mar 10, 2019


1- SRT10KXLI problem, it showing on screen (Internal RBC needs Replacement on Battery). 2- SRT6KXLI problem, During normal working day the smoke came from the power supply when we off the UPS after a few hours when we reconnect to the power the UPS cut the Main power feus.

APC Computers &... • Answered on Jan 30, 2019


APC lists the SURTA3000XL and SURTD3000XL on their regional web sites. In either case, the red X indicates an internal fault. If the unit is under warranty, contact APC for repair. Otherwise, replace the UPS. See page 15 (page 16 of the PDF) of the manual, available oon the product page: https://www.schneider-electric.com/en/product/SURTA3000XL_APC/apc-smart-ups-rt-3000va-120v/ . The current link to the manual is http://download.schneider-electric.com/files?p_enDocType=User+guide&p_File_Name=ASTE-6Z8LQA_R2_EN.pdf&p_Doc_Ref=APC_ASTE-6Z8LQA_EN . Since the unit isn't charging, the charging circuit is either damaged or after the faulty wiring inside the unit. Unplug the UPS and do not try to use it. I wish that I had better news for you. Cindy Wells

APC Computers &... • Answered on Jan 02, 2019


First cheack the supply if supply is present the then cheach the cable which is connected between power supply and the ups if this things are working properly then open the ups and then go to the power supply section by tracing the ip put from the power supply switch you will find the fuse over there

APC Smart-UPS... • Answered on Dec 22, 2018


Hi and welcome to fixya sir please elaborate your problem i cant get it for what problem you are looking for a solution

APC Computers &... • Answered on Oct 01, 2018

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top APC Experts

Cindy Wells

Level 3 Expert

6259 Answers

Jax Planet
Jax Planet

Level 2 Expert

923 Answers

Joe Goldman
Joe Goldman

Level 2 Expert

337 Answers

Are you an APC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...