Amana Washing Machines - Recent Questions, Troubleshooting & Support


Your pressure switch is having problems.
Or could be the hose is pinched or some how was disconnected.
Here is what the part looks like and you can buy it here.
https://www.genuinereplacementparts.com/amana-ntw4800vq0-water-level-pressure-switch-genuine-oem?msclkid=3b99d76add8f196fb92d88442ec2a1ab

Amana Washing... | Answered on Aug 08, 2020


The F8 E1 code indicates a problem with the water coming into the washing machine for most Amana washing machines. This could indicate a problem with the inlet valve of the washer, the water hoses or your incoming water pressure. First make sure that the shut-off valves for the washer water lines are open. Close these valves and disconnect the water lines. Keep a bucket handy to catch the water in the hoses. Check the filters for debris and clean out any clogged filters. (Check both at the shut-off and the washer inlets.) Connect the hoses to the shut-off valves and check how much water flows into your bucket. (Some hoses are designed to limit flooding and restrict the flow when the hose is damaged. Replace the hoses if they are older or limiting your water flow.) Connect the hoses back to the washer.

Next do you get water flowing into the washer when you start the machine? If possible, try both a hot cycle and cold and check for different flow rates. (We had the inlet valve on a washer fail to provide full flow for hot water. Replacing the valve cured the problem.) Replace the valve, if it's not opening properly. If you are getting good water flow, you might have a problem with the water pressure/flow sensor. There could be dirt blocking air flow in the tubing to this sensor. Clean out the tubing or replace the sensor. The problem could also be with the wiring or the control board not getting the messages to and from the inlet valve or pressure sensor.

I hope this helps. The parts diagrams for the NTW4516FW2 are available from Sears Parts Direct: https://www.searspartsdirect.com/model/1l5hhsznio-001268/amana-ntw4516fw2-washer-parts .

Cindy Wells
(With the faulty inlet valve, we were able to improve the water flow temporarily. We took off the hot water line and filled it with household vinegar while turning on and off the washer. This dissolved the calcium carbonate deposits inside the valve.)

Amana Washing... | Answered on Jul 04, 2020


Try unpluging power cord to reset. Otherwise, Owner's manual, no manual? Try https://www.manualslib.com

Amana Washing... | Answered on Jun 29, 2020


check to see if spins if ok check water solenoid

Amana Washing... | Answered on Apr 16, 2020


Washer will not drain:
Thedrain water pumpis the main part in your washing machine that pumps out the water. If this is defective or has failed in any way, this will be the reason why your washer will not drain the water. Before you order a new drain pump, make sure tocheck the pump to be sure a small object like clothing or similar has not lodged itself insideof it causing the NO DRAIN issue and even a no spin issue?. If the drain pump is not clogged, you can test it with a multimeter and remove and replace if needed.

Read more: http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/#ixzz3X2LbXMWJ
The washing machinedrain hoseis where the water flows through to get the water out.If this drain hose is blocked, kinked, bent, or clogged, the washer will NOT be able to remove the waterfrom the tub. Check the drain hose to be sure it allows the water to flow freely. You can take the drain hose off and run water through it in your sink to be sure it is not blocked. If there is water STILL in the washer when you remove the drain hose, grab a bucket as the water will exit from where you disconnected it Thewater pump belt(to drain out the water) may have broke or become frayed or loose.If this belt breaks then it is unable to drain and remove the water from your washer. Inspect the belt to see if this is causing theNO DRAINissue and remove and replace if needed.

If thelid switchis not working as required it will cause your washer to not drain (and many other problems).This may be unlikely as a bad lid switch will usually cause your washer to alsonot agitate or spin.However on some models this can vary. The best thing to do if you have a suspected bad lid switch is to test it. It can fail electrically and or mechanically. If mechanical failure is the issue, you should be able to see if it is cracked, broken, or not in place to make contact with the lid. To test it electrically, use a multimeter set on Ohms and test it for continuityMy advice is free cuz God is good!


water pump belt broken104-undefined-undefined-0.jpg

water pump hose washer clogged washer hose1-undefined-undefined-2.jpg

water pump sump dirty-undefined-undefined-5_2.jpg

water pump2-undefined-undefined-9_0.jpg

Amana Washing... | Answered on Mar 19, 2020


https://www.youtube.com/watch?v=kFLbBdZGjDg

https://www.youtube.com/watch?v=4Nx8_nbqCVw


A grinding noise is commonly caused by a malfunction or failing of one of the following parts of the machine. ... They consist of four small pieces of plastic which, over time, wear out and begin slipping, which produces the grinding noise when the machine is in the agitate cycle.

https://www.appliance-insurance.co.uk/appliance-insurance-articles/help-my-washing-machine-makes-grinding-noises/




Amana Washing... | Answered on Mar 12, 2020


The lid lock is a safety feature and can't be bypassed. You have to fix the problem not find a way around it. A couple of years ago a young boy had his arm torn off.

www.partselect.ca > Models > NTW4605EW1

NTW4605EW1 Amana Washer Parts and Repair Help

Get Parts and Repair Help for NTW4605EW1 Amana Washer - WASHER. ... The lid switch assembly detects if the washer lid is open or closed and prevents the ...

Amana Washing... | Answered on Jan 28, 2020


no such thing

Amana Washing... | Answered on Dec 17, 2019


The model number is probably NTW4605EW0. Most appliance models from this manufacturer end with a number. Sears Parts Direct has the Use and Care manual for the NTW4605EW0 here: https://www.searspartsdirect.com/manual/sblu1hn6dz-001268/amana-ntw4605ew0-top-load-washer . Amana has addtional documents for the washer on their support page: https://owners.amana.com/user-manuals/ . Use the drop-down menu and search box to locate the manuals and installation guide. The current link to the manual (in English) is http://shared.whirlpoolcorp.com/assets/pdfs/literature/Use%20and%20Care%20Guide%20-%20W10740545.pdf .

I hope this helps. I don't see a printed copy of the manual available from Sears Parts Direct. You can print it yourself or take the file to a print shop (Kinkos, UPS store) later.

Cindy Wells

Amana Washing... | Answered on Nov 05, 2019


if the lid lock is broke it shouldn't be doing anything.
If it is broke, it needs to ne fixed/replaced.
If it is doing other things, more troubleshooting is necessary.

Amana Washing... | Answered on Nov 03, 2019

Not finding what you are looking for?
Amana Logo

1,978 questions posted

Ask a Question

Usually answered in minutes!

Top Amana Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Mike

Level 3 Expert

4369 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...