Amana Logo

Amana Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 1K Products
  • 75K Answers
  • 2M Views

not sure i use mine without exhaust hose

Amana AP095R... | Answered on May 27, 2020


I know this is late but I had to add a solution to this problem since I had the exact same problem and was able to solve it. The probelm is not your control board. On these units, the heat pump compressor will not kick in unless the temperature you set on the control panel is within 2-1/4 degrees (or 4 degrees depending on your unit model. Otherwise, the unit locks out the compressor until the electric heat coil bring the indoor temperature up to that level - and then will switch the compressor back on for heat pump operation. So the problem is not the control panel or the compressor, it the electric heat coil. The coil has two manual limit switches on it that may be tripped and should be checked. The coil can be easily accessed by shutting down the power, removing 4 screws around the air outlet, pushing the screen up and sliding the panel out the top. The power wires can remain in place while the limit switches are reset. Hope it works.

Amana... | Answered on Apr 20, 2020


check to see if spins if ok check water solenoid

Amana Washing... | Answered on Apr 16, 2020


GO SEE A DEALER

Amana Kitchen... | Answered on Apr 09, 2020


if voltage to heater element bad element if no voltage bad control board

Amana Heating &... | Answered on Apr 01, 2020


check manufacurer tech support for info

Amana Heating &... | Answered on Apr 01, 2020


Washer will not drain:
Thedrain water pumpis the main part in your washing machine that pumps out the water. If this is defective or has failed in any way, this will be the reason why your washer will not drain the water. Before you order a new drain pump, make sure tocheck the pump to be sure a small object like clothing or similar has not lodged itself insideof it causing the NO DRAIN issue and even a no spin issue?. If the drain pump is not clogged, you can test it with a multimeter and remove and replace if needed.

Read more: http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/#ixzz3X2LbXMWJ
The washing machinedrain hoseis where the water flows through to get the water out.If this drain hose is blocked, kinked, bent, or clogged, the washer will NOT be able to remove the waterfrom the tub. Check the drain hose to be sure it allows the water to flow freely. You can take the drain hose off and run water through it in your sink to be sure it is not blocked. If there is water STILL in the washer when you remove the drain hose, grab a bucket as the water will exit from where you disconnected it Thewater pump belt(to drain out the water) may have broke or become frayed or loose.If this belt breaks then it is unable to drain and remove the water from your washer. Inspect the belt to see if this is causing theNO DRAINissue and remove and replace if needed.

If thelid switchis not working as required it will cause your washer to not drain (and many other problems).This may be unlikely as a bad lid switch will usually cause your washer to alsonot agitate or spin.However on some models this can vary. The best thing to do if you have a suspected bad lid switch is to test it. It can fail electrically and or mechanically. If mechanical failure is the issue, you should be able to see if it is cracked, broken, or not in place to make contact with the lid. To test it electrically, use a multimeter set on Ohms and test it for continuityMy advice is free cuz God is good!


water pump belt broken104-undefined-undefined-0.jpg

water pump hose washer clogged washer hose1-undefined-undefined-2.jpg

water pump sump dirty-undefined-undefined-5_2.jpg

water pump2-undefined-undefined-9_0.jpg

Amana Washing... | Answered on Mar 19, 2020


usually in back on top of or near compressor or in the front of fridge u have to remove the panel to see it

Amana... | Answered on Mar 12, 2020


pan is usually located on back or front bottom you may have to remove back or front pANEL TO ACCESS


drain fridge-drain-pan-undefined-undefined-0.jpg

Amana... | Answered on Mar 12, 2020


https://www.youtube.com/watch?v=kFLbBdZGjDg

https://www.youtube.com/watch?v=4Nx8_nbqCVw


A grinding noise is commonly caused by a malfunction or failing of one of the following parts of the machine. ... They consist of four small pieces of plastic which, over time, wear out and begin slipping, which produces the grinding noise when the machine is in the agitate cycle.

https://www.appliance-insurance.co.uk/appliance-insurance-articles/help-my-washing-machine-makes-grinding-noises/




Amana Washing... | Answered on Mar 12, 2020


gently possible soft brush or coil comb

Amana... | Answered on Mar 11, 2020


Goodman Industries has purchased Amana. So go to Goodman website for info. Without model number I cannot look up error code

Amana Heating &... | Answered on Feb 19, 2020

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Amana Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6101 Answers

Brad Brown

Level 3 Expert

18342 Answers

Are you an Amana Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...