Aiwa Logo

Aiwa Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 500 Products
  • 5K Answers
  • 365K Views

There's no clear all settings there. You need to manually delete each saved station. Try to unplug the power of the unit for few hours and check if that clears all.

Aiwa Audio... | Answered on Jul 13, 2020


hello
there is a belt inside which has to be replaced with a new one. it dont cost much but disassembling needs a bit braveness...
please feel free to contact me under your topic for further assistance.
regards

Aiwa XR-MS5 CD... | Answered on Jul 11, 2020


Check for power at the wall outlet.

Check for fuses at the rear.

Take it to a service centre.

Aiwa Audio... | Answered on Jun 22, 2020


if your vcr is a multisystem, select the proper system in your vcr for the video to be played. but if not, you cannot play your PAL in your NTSC vcr. good luck!

Aiwa HV-MX100... | Answered on Jun 01, 2020


https://www.manualslib.com/manual/3586/Aiwa-Ts-W45.html

Aiwa Audio... | Answered on May 18, 2020


For Aiwa brands, once it has been locked, that it is.

Aiwa Televison &... | Answered on May 17, 2020


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Aiwa XD-DV370... | Answered on Mar 22, 2020


YOU TELL US WE DO NOT HAVE IT HERE

Aiwa Audio... | Answered on Feb 09, 2020


Lift felt on platter and and lift the platter section off the unit by putting your thumb and forefinger through the two large holes and pull upwards.There should not be any special routing for the belt and should go directly onto the spindle motor to your platter. Place the belt around the inside rim of the platter while it is still off the unit. Now replace the platter and move the platter around until you see the spindle motor through one of the holes. Use some tweezers to manouvre the belt onto the spindle motor. On some units you will have to lay the belt out inside the unit, replace the platter and manouvre the belt onto the platter. Hope this helps

Aiwa PX-E860... | Answered on Jan 22, 2020


I own a NSX-MT960 and the same thing happen , DEAD DISPLAY.

I just happen to be retired Certified Electornic Tech and Held a FCC first class ticket, and own a tv-vcr -stereo repair shop that worked on all brands,

I had to fix alot of items WITHOUT THE HELP of a schematic diagram and got to be pretty good at it,

THIS HAPPENED about 7 or 8 years ago, but it still may help somebody,

THE DISPLAY IS A VACUUM FLOURESCENT and has a low voltage heater circut to heat it up like old vacuum tube, AIWA PUT IN A SURGE CURRENT LIMIT RESISTOR about a 1/2-1 watt unit with LOW OHMS, I FORGET NOW BUT a 1 watt .5 ohm resistor will fix it, OR JUST JUMP IT for a short time to test, but put that thing back in, better to burn out that resistor than the heater circuit in the display.

HOPE THAT HELPS

RETIRED TELEVISION REPAIR ENGINEER THAT TROUBLE SHOT DOWN TO THE COMPONET LEVEL< NO BOARD CHANGER HERE!!

THAT WAS THEN < THIS IS NOW, NOW YOU HAVE TO CHANGE BOARDS DUE TO SMD WAVE SOLDERING , YOU WILL RUIN A PCB WITHOUT TENS OF THOUSANDS OF DOLLARS WORTH OF DESOLDERING EQUIPMENT.

BEST REGARDS

Aiwa Z-HT65... | Answered on Dec 29, 2019


Strip it down sufficiently to gain access, then release the latch internally.

Aiwa Audio... | Answered on Nov 28, 2019


Measure the diameter.

Aiwa Audio... | Answered on Nov 27, 2019


Hi JACQUELYN MOORE, so you say you have problems in the function control system, you might have some of the keys locked and that does not answer any other
Check all the keys and see if any are locked
and comment

Hola JACQUELYN MOORE, por lo que comentas tienes problemas en el sistema de control de funciones, puede ser que tengas alguna de las llaves trabadas y eso hace que no te responda ninguna otra
Revisa todas las llaves y ver si alguna esta trabada
y comenta

https://www.manualslib.com/products/Aiwa-Cx-Zr525-372985.html

Aiwa Audio... | Answered on Sep 24, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

Top Aiwa Experts

The Knight
The Knight

Level 3 Expert

76407 Answers

 Grubhead
Grubhead

Level 3 Expert

5700 Answers

Tom Chichester

Level 3 Expert

56021 Answers

Are you an Aiwa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...