Admiral Washing Machines - Recent Questions, Troubleshooting & Support


try check drain motor below the drum or maybe your hose drain is blocked by something

Admiral Washing... • Answered on Apr 08, 2021


The only way to bypass this switch is fist pill the plug, gain access to the switch from under the hood. put a jumper wire on the 2 wires on the switch. that will do it. I hope this helps you out.

Admiral AAV7000A • Answered on Mar 27, 2021


Usually indicative of a previous was with a tissue left in a pocket. Run a hot wash, large load setting with detergent and the machine empty. That gives plenty of water, and detergent to keep the lint in suspension and be pumped out.

Admiral Washing... • Answered on Dec 29, 2020


WASHER WILL NOT RINSE: If your washer doesn't go through the washer rinse cycle, the most likely cause is the water valve. What happens is thewater valvewill stop letting cold water into the washer; therefore, once the washer gets to rinse it will either stop or not do anything during the whole rinse cycle. This is because when you selected your water temperature, youmay haveselected warm/cold or hot/cold. The hot water came in and you didn't notice any problems. When it got to rinse, the cold water the cold water won't come in. Therefore, the washer does nothing. Theitem to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going tourwater inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test. Another test u can do to check thewaterinletvalve,first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed. . If you still don't have good water pressure, the problem is in your house plumbing and you need to call a plumber. If you had good water pressure the first time you performed the test, the water valve is bad and needs replacing. If you still don't have good water pressure, the problem is in your house plumbing and you need to call a plumber. If you had good water pressure the first time you performed the test, the water valve is bad and needs replacing. TIMER If your washer doesn't go through the washer rinse cycle the timer may be the problem. Sometimes the timer gets stuck in the middle of the cycle or won't turn at all. If the washer runs,but the timer doesn't turn, the timer is bad and needs replacing. Do you have anti-flood hoses leading to the machine. If you do there is probably a loose tube in the back causing a small leak. When the hoses detect that water is still flowing after a certain amount of time due to the leak it shuts down and causes the machine to turn off during the rinse/spin cycle By the way my advice is freecuzGod is good! inlet voltage test waterinlet valve-undefined-undefined-0.jpg inlet dirty water inlet screen-undefined-undefined-2.jpg inlet how2clean inletvalvewest_washer4-undefined-undefined-5.jpg inlet testing washerwater inlet valve-undefined-undefined-9.jpg

Admiral Washing... • Answered on Mar 16, 2020


What is the model number of the unit?

Admiral Washing... • Answered on Sep 24, 2019


Do you check to see if it's belt driven? If it is your belt might have come off or needs to be replaced

Admiral Washing... • Answered on Jun 13, 2019


Belt slipping or transmission clutch bearings are on the way out.

Admiral Washing... • Answered on May 03, 2019


Timer or control board issue most likely. If it has a start button, make sure it’s not stuck

Admiral Washing... • Answered on May 01, 2019


The seal has cracked and will need to be replaced. Part of it is in the drive block attached to the basket and is probably your failure. All you need to remove is the maytag tool and a strong arm.

Admiral AAV7000A • Answered on May 01, 2019

Not finding what you are looking for?
Admiral Logo

1,074 questions posted

Ask a Question

Usually answered in minutes!

Top Admiral Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Brad Brown

Level 3 Expert

18666 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Are you an Admiral Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...