...LG washing machine last week and with the help of this great site I fixed it by changing the hall sensor. I got through 5 loads and it happened again. GGRRRRR! Please Help. This time the motor moves ...
Question about WM-2277HW Front Load Washer
test mode Not sure if it's rinsing properly The machine tests itself when power is applied, if there is a problem it will indicate the problem via an error code on the display. If you suspect that the
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
test mode? do you know the button combination to put the washer in test mode? i believe it is the power button along with the two center buttons on the right. The washer must be empty and the controls
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
...when the START/PAUSE button is first pressed in the QC Test Mode. The machine's program is stored in the EEPROM area of the microcontroller unit, when it is out of order the machine stops
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
TEST MODE. On most LG washers---the Test Mode is enabled by pressing and holding the SPIN SPEED and SOIL LEVEL buttons---and then pressing the POWER button (release all 3 buttons and wait for the door
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
...the power button then the machine will go into test mode. Each subsequent push of the start button will go to the next test item, ie, spin, water fill, drain, etc. Might give it a try. Good
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
...test mode. What could be the problem? Got LE error code. Put washer in diagnostic mode and when in spin tests it spun. Got no error codes. Put washer into Rinse & Spin mode with no cloths loaded. ...
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
...test mode drum spins, but at the same speed for all test mode settings. I assume this is because it is not getting an RPM reading. what else can I check? Replace Hall effect sensor(speed sensor) $20 ...
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
...a $6 part and pretty easy to do. Try cold only wash and see if it works. Also, try putting washer into test mode and run through each segment that it tests. Let us know results by commenting back ...
Question about WM2701HV Front Load Ultra Capacity Washer with Wash Motion Technology, Graphite Stee4.5 cu.ft. Ultra Capacity with NeveRust Stainless Steel Drum IEC, Direct Drive Motor for the Ultimate in Durability and Reliability, 10 TilTub for Easy Reach into the
Test Mode? How do I enter test mode on a LG WM6700HBA front load washer? I've read holding SPIN and SOIL then press POWER, but this model is touch screen. I've tried holding the areas of SPIN and SOIL
Usually answered in minutes!
9,125 Questions
3,839 Questions
3,158 Questions
2,979 Questions
2,660 Questions
