I am facing problem with V Touch, When i am starting my V-Touch Welcome screen is displayed along with message as Please Wait but i am unable to proceed further. Kindly help me in solving the problem, Kindly send me the solution on [email protected]

try to turn it off. get the network cable out the machine. wait 1 minute. press 6-stop-powersave (all 3 at the same time, powersave top right corner) With these buttons pressed, start the machine and keep the buttons down until machine is fully started.

push reset button with safety pin or tooth pick

Hi!
That error often occurs on school networks and there are a few things we can have you try. Please email us as [email protected] and we'll get started!
Thanks! Kyle Levenick Director, Subscriber Relations BrainPOP

The error message "Clean Unable 46" is an indication that the machines ink absorbers are full or almost full. The ink absorbers hold liquid and dried ink after it has been purged from the print head. These absorbers can control enough ink for the expected life of the machine.

There is a possibility that this message may have occurred in error. Upgrading the firmware of the Brother machine may resolve the issue. Follow the procedure below to determine if a firmware update is required:
-if the display screen is displaying an error message, press the STOP/EXIT key to change the LCD to the main screen.
-press the # and * key at the same time. The first 2 characters on the top row will determine the ROM version.

If the ROM version is OE or greater (example: OF, OG, OH, etc), the firmware does NOT need to be upgraded. If the ROM version is OA, OB, OC or OD, follow the procedure on this link to upgrade the firmware.

If the message "Clean Unable 46" continues to appear on the display the Brother machine after completing the firmware upgrade and your machine is within warranty (even if it's not under warranty you have to do the same thing), you have to take it to a Brother Authorized Service Center. http://welcome.solutions.brother.com/BSC/public/us/us/en/faq/faq/000000/002600/000059/faq002659_000.html?reg=us&c=us&lang=en&prod=mfc290c_all&Cat=11

In order to calibrate the nuvi 700 or 705 series touch screen, follow the instructions below.

1. Start with the unit powered OFF and unplugged from power supply.
2. Press and hold your finger anywhere on the touch screen.
3. Next, slide the power switch ON and immediately slide it into the Lock position. There is no need to wait for the screen to flash on or show the Garmin logo before moving the switch into the Lock position.
4. Leave your finger on the screen for about 45 seconds.
5. Two intersecting lines should display on the screen along with the message: Press Dot.

Follow the rest of the on screen prompts to complete the screen recalibration. Once it is completed the unit will display Calibration Complete

return it that is a well known problem and that happens to every 4 out of 10 vtouches just send a note explaining the situation and that you want a new one

In order to recalibrate the nuvi® 7xx's touch screen, follow the instructions below.

1. Start with the unit powered OFF and unplugged from power supply.
2. Press and hold your finger anywhere on the touch screen
3. Next, slide the power switch ON and immediately slide it into the Lock position. There is no need to wait for the screen to flash on or show the Garmin logo before moving the switch into the Lock position.
4. Leave your finger on the screen for about 45 seconds.
5. Two intersecting lines should display on the screen along with the message: Press Dot.

Follow the rest of the on screen prompts to complete the screen recalibration. Once it is completed the unit will display Calibration Complete

I am not 100 percent what you are asking but I will answer the best I can with your question.

1. Press the [Administration] button located above the numeric keypad on the Control Panel. The Administration button has a wrench symbol located above it. The Access screen will be displayed.
2. Select [Tools] on the Touch Screen. The Tools Access Number screen will be displayed.
3. Enter your numeric password using the keypad.
   
   NOTE: If you do not know the password, contact your administrator. The initial password at machine install is 11111.
   
   If the administrator encounters a problem with changing or forgetting the machine password, a service call must be placed:
   
   
4. Select [Enter] on the Touch Screen. The Tools screen will be displayed.
5. Select [System Image Quality]. The System Image Quality screen will be displayed.
6. Select [Image Recognition]. The Image Recognition screen will be displayed.
7. Select 'Screening Adjustment' by selecting the [Up] or [Down] arrow buttons.
8. Select [Change Settings]. The Screening Adjustment screen will be displayed.
9. Select [Apply to Copies Only] then select [Save]. The Screening Adjustment screen will be displayed.
10. Select [Close]. The System Image Quality screen will be displayed.
11. Select [Auto Screening Adjust]. The Auto Screening Adjust screen will be displayed.
12. Select [Halftone Screen]. The Halftone Screen will be displayed.
13. Select either [Halftone 200 line screen] or [Photograph 200 dpi].
    
    NOTE: Do not select 'Printer use' as this will effect print calibration; which will be handled directly by the color server set up to print to the copier / printer.
    
    
14. Select [Save]. The Auto Screening Adjust screen will be displayed.
15. Insert at least 2 sheets of white, 216 mm x 279 mm (Letter, 8.5 x 11 inch) paper in Paper Tray 5 (Bypass Tray).
16. Select [Print Test Original] to print a sample of the settings. The message 'Please wait…Printing test original' will be displayed and the test original will print.
    
    NOTE: If selecting [Print Test Original] displays the message ‘System Disabled' then Screening Adjustment is disabled. Select [Close] and repeat steps 5 to 16.
    
    
17. Open the Document Glass Cover.
18. Place the test original face-down on the Document Glass with the two magenta squares against the left edge of the glass.
19. Place 5 sheets of blank white paper directly on top of the test original.
20. Close the Document Glass Cover.
21. Select [Start Adjustment] from the Touch Screen. The message 'Please wait….Adjustment in progress' will be displayed, then the Auto Screening Adjust screen will be displayed.
22. Select [Adjustment Complete]. The message 'Please wait…Printing current settings' will be displayed and the adjusted original will be printed.
23. Examine the adjusted original to make sure the image quality is satisfactory and continue to the next step. If the image quality is not satisfactory repeat steps 12 through 22.
24. Select [Close]. The System Image Quality screen will be displayed.
25. Select [Close]. The Tools screen will be displayed.
26. Select [Close]. The default copy screen will be displayed

You need to replace the battery