Question about Sony Cyber-Shot DSC-F828 Digital Camera

1 Answer

Firmware update problem

I downloaded the firmware update 2.0, copied the extracted firmware file F828V2.ash to the root directory of my memory stick, put it in the camera's memory stick slot, turned the camera?s mode-switch to "SETUP", held down the "MENU" button, and switched on the camera (batteriy full, 174min left). and here we go : 1. no message "No file in this folder" on the LCD screen. 2. on the camera-screen-menu, "SETUP 2", there is no "VERSION" entry. i tried with AC power adapter, different memory / pro sticks and compact flash cards, but always the same. what's wrong ?

Posted by Anonymous on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 255 Answers

Hello! I experienced the same problem. I did not updated the firme ware because my F828 already came with latest version. To view the firmeare information in your camera you must have the AC power adpater conected otherwise it wont show. This is all I know. From here I think you have only to follow the steps of SONY guide. Hope I could help in any way.

Posted on Sep 13, 2005

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was adding a game in my psp version 6.60, but when i opened the games in memory stick, there was no game, just a message came "There is no games...". I failed to find its proper solution so please help...


I had this problem (same firmware), and this is what I did. It works a treat. You need to downgrade from OFW (Official Firmware) 6.60 to 6.20, and then install CFW (Custom Firmware) 6.20. This guide shows you how to downgrade and gives you the program to do it:

http://pspslimhacks.com/6-xx-downgrader-v4-released/

Here is the 6.20 official firmware:
http://www.mediafire.com/?6kj00wdwe8nwfzp

When both of those have been downloaded, extract them to X:\PSP\GAME, where X is the drive your PSP is in.
Disconnect your PSP and turn it on. Then go to your memory under the Game section on the XMB. Run the downgrader (you need at least 75% battery, otherwise the program will kick you off). When the update's at about 85%-90% you may get an error, but don't worry about it. After it's installed, it should boot and show you a blue screen. Press circle. When you load up again, feel free to delete the update files from your memory stick. Then reconnect your PSP.
Now that you've downgraded to 6.20, you'll be able to permanently mod your PSP with custom firmware.
Download this and extract the folders to the root of your PSP (don't worry about overwriting; the folders merge):
https://code.google.com/p/procfw/downloads/detail?name=620PRO-C2.rar&can=2&q=#makechanges
Disconnect your PSP again and head to the memory stick section under Game in the XMB. Run the Pro Update program.
Your system should reboot.
Go back to Game > Memory Stick Utility, and then click on the permanent patch. It'll ask you if you want to install the patch. Press X.
It'll tell you that it's saved a file. Run it on the fake vshmain.prx. Connect your PSP to your computer and copy the file (vshorig.prx) to your desktop. If your PSP bricks (unlikely), putting that file back on should unbrick it.
After that, run the permanent patch again on your PSP but this time press circle to go past saving the file and install the custom firmware.
Now, if you're trying to put PSP ISO files on your console, you need to create a folder called "ISO" without quotation marks in the root of your PSP. When you download a PSP ISO, they go in this folder.
If you want to play PS1 games on your PSP, you'll need to create EBOOT files from the disc images you download. Just follow this tutorial and you should be fine.
http://www.epforums.org/showthread.php?55562-GUIDE-Convert-PSX-game-to-PSP-Eboot-w-psx2psp

You can download emulators and run those, too. Happy pirating! ^_^

Jan 27, 2013 | Sony Psp 3000 Hdwe System Portable Gaming...

1 Answer

Today I found a firmware update v102 for the EX-S200 Silver model. I want to update this firmware as the color of the picture taken is extremely bad compared to a 3 year old Nikon 10 megapixel. My less...


I doubt this will take care of the problem. The root directory of the drive is the removeable sd card from the camera and it is above the level of the BIN folder. You then plug the sd card back in the camera and hold down the set button. The whole process is outlined http://support.casio.com/download.php?rgn=1&cid=001&pid=987

Mar 01, 2017 | Cameras

1 Answer

FIRMWARE for Sanyo xacti vpc-hd2000!?


s_ustext_software.gif
leer.gif
Updating Firmware on Xacti HD2000

This page explains how to download and install the firmware update for the VPC-HD2000.
  • This firmware is for the VPC-HD2000 only. Please do not install it on another model.
  • By installing this firmware Greek, Swedish and Finnish will be added as new menu languages. (Please notice that for this purpose the menu languages Traditional Chinese, Simple Chinese and Korean will be deleted!)
    It is not necessary to install this firmware update when there is already the possibility of choosing Greek, Swedish or Finnish as menu language! Please check this before continuing with the update.
  • Before updating the firmware, please read through the explanations on this page.
  • Make sure to update the firmware in the order shown below.
  • The camera might not boot up properly if its power is turned off during the firmware-updating procedure.
  • Please read the accompanying licensing agreement before downloading this firmware. Downloading the firmware automatically implies your acceptance of the licensing agreement.
Requirements:
  • SD memory card (henceforth referred to as "card") with capacity over 8 MB.
  • Fully charged lithium ion battery.
  • Additionally, you need one of the items listed below:
    (i) A SD memory card reader (henceforth referred to as "card reader")
    (ii) A dedicated USB interface cable (shipped with the camera).
CAUTION
Be sure not to take out the battery during the updating procedure (this lasts about 60 seconds).
Avoid operating the buttons on the camera or closing the monitor unit during the updating procedure.


I) Preparing to update (copying the firmware onto a card)

Step I.1: Format the card on your camera*
  • Turn the camera on and set the "REC/PLAY"-button to "PLAY"
  • Press the "MENU"-button.
  • Move joystick to the left and select "OPTION MENU 3".
  • Move joystick to the right and select "FORMAT". Press the "SET"-button.
  • Select "FORMAT". Press the "SET"-button.
  • Select "YES". Press the "SET"-button.

    *CAUTION
    If you format a card, all images and data stored on that card (whether protected or not) are deleted! Please be sure to move or copy important images and data to a PC or to another card!
Step I.2: Download the Firmware*
  • The firmware can be downloaded here.

    icon_dl1.gif Firmware Update XACTI HD2000
    s313n081.bin (7.5 MB)
    *CAUTION:
    Please be sure to download the file onto a hard drive and not onto a removable location such as a card reader.
    The firmware file should be saved in a location where you can easily find it again later (e.g. save it on desktop of your computer).


Step I.3: Copy the file "s313n081.bin" to the formatted card (from step I.1):

The method of operation differs depending on whether you use a card reader (i) or a dedicated USB cable (ii).
(i) When you copy the downloaded files with a card reader: (1) Put the formatted card from step I.1 in the card reader. (2) Copy the "s313n081.bin" file created on your hard disk in step I.2 to the root directory of the card.

firmware_hd2000_1.jpg

(ii) When you copy the downloaded files with a dedicated USB cable: (1) Connect the camera to your PC with a USB cable and turn on the camera. When you connect to your PC, please make sure the camera's USB interface is set to "Card Reader". (Please refer to "Setting the Connection Mode" on pages 7 to 8 of the Instruction Manual in the Xacti Software CD 1.0) Please make sure the camera is recognized as a removable disc. (2) Put the formatted card (from step I.1) in the camera and then copy the "s313n081.bin"-file created on your hard disk (in step I.2) to the root directory of the card.

firmware_hd2000_2.jpg

(3) Remove the camera from computer.
Please read "Dismounting the Camera" on pages 9 to 11 of the Instruction Manual in the Xacti Software CD 1.0 for a description of how to disconnect the camera.

II) Updating firmware on the camera itself

CAUTION>:
Do not turn off the power during the updating procedure (this lasts about 60 seconds)!
  • If the power is turned off during the updating procedure, the update may not be properly completed and the camera may not start up.
  • To prevent the battery from running out during the updating procedure, please use a fully charged Lithium ion battery.
  • Do not remove the battery during the updating procedure.
  • Do not operate the buttons on the camera or close the monitor during the updating procedure.

Step II.1: Insert the card with firmware-update file (from step I.1) into camera

Step II.2: Turn the camera on and set the main switch to "PLAY".
  • The playback screen will be displayed.
  • If the camera is in SIMPLE mode, switch it to NORMAL mode.
Step II.3: Press the "MENU"-button.
  • The menu screen will be displayed.
Step II.4: Choose "OPTION MENU 3"

Step II.5: Choose "FORMAT" from the Menu Screen, but do NOT go into "FORMAT"

Step II.6: Move joystick to the left for more than 2 seconds.
  • The update screen will be displayed.*

    *No Update Screen
    If the update screen is not displayed, it's possible that the update file was not copied onto the card. Please refer to "Preparing to Update" to copy the update file onto the card and follow the updating procedure once more.
    If the main switch is set to "REC", the update screen will not be displayed. Make sure the main switch is set to "PLAY".
Step II.7: Choose "YES" and press the "SET"- button.
  • Updating will start.
  • During the updating procedure, the screen will show the message, "LOADING. DO NOT POWER OFF", and the access light will flash.
    Please do NOT turn the power off during the updating procedure! (this takes about 60 seconds).
Step II. 8: When the updating procedure is completed, the camera will turn off automatically.
  • Please remember to format the memory card once more before using it again.

Oct 15, 2010 | Sanyo Xacti VPC-HD2000 High Definition...

1 Answer

R4 for nintendo ds lite does not work


Make sure that you have the latest firmware installed in your R4 micro SD card. You can get the latest firmware here:
http://en.r4ds.me/kernel/English-1.18.rar

After downloading, extract the .rar file. Copy "_DS_MENU.DAT" and "_DS_MSHL.NDS" to the root directory of your micro SD (ex: E:\ or F:\),
To play games, simply copy the games you have downlaoded to the root directory also.

Apr 03, 2010 | Nintendo DS Lite

1 Answer

I want free downloads of sony psp3000 memory stick games


Hi,

For you to download and play games on your psp, please follow the steps listed herein;

1. Since you can download directly to your PSP memory stick, you'll have to download to your computer and further transfer to your PSP memory stick.

2. You'll have to modify the PSP from the official version to a custom version. You can find out how to do this by typing in this search "How to hack PSP to custom firmware"

You can now do the following to transfer and play games;


a. Get a good memory stick. I recommend that you get a Memory Stick Duo in at least a 1 GB size, though a 2 GB is even better.

b. Find and download the PSP games you want. If you don't know where to find the games try a download service. A good one will let you have unlimited downloads for a small one-time fee. You can see the link below for more information.

c. Unzip the game files and save them somewhere that you can find them easily, like your desktop.

d. Plug your PSP USB cable into your PSP and your computer.

e. For PSP games- go the the root directory on your PSP then make a folder called ISO. (If you downloaded PSOne games, go to the root directory on your PSP and find the folder called PSP/GAME.)

f. Copy the PSP game files into the ISO folder. (Copy PSOne game files into the PSP/GAME folder.)

Once this is done you can now play games on your PSP.

Regards

Mar 29, 2010 | Sony PlayStation Portable (PSP) Console

1 Answer

I downloaded the firmware update for my sharp bp-hp20 blue ray player but my player won't recognize the file on my memory stick. Any suggestions?


There are usually two reasons that this happens 1. is that the file needs to be extracted first to the root of the drive ie. not in any folders. 2. is that some of the older sharp products won't reckonize any usb memory larger than 1GB. As is the case with my 52' Sharp AQUOS Special Edition LC-52SE94u TV. Could not read a 2GB Kingston, but reads the 1GB Kingston just fine to update firmware. And Sharp doen't tell you this not even in the online how to firmware update page.

Hope this solver you problem,
Scott

Mar 21, 2010 | Sharp AQUOS Blu-ray Disc Player

1 Answer

How do u put cheat codes on a sony psp


Hi,

1st your PSP needs to hacked to a custom firmware, follow these procedures;


1. Since you can download directly to your PSP memory stick, you'll have to download to your computer and further transfer to your PSP memory stick.

2. You'll have to modify the PSP from the official version to a custom version. You can find out how to do this by typing in this search "How to hack PSP to custom firmware"

You can now do the following to transfer and play games;




a. Get a good memory stick. I recommend that you get a Memory Stick Duo in at least a 1 GB size, though a 2 GB is even better.


b. Find and download the PSP games you want. If you don't know where to find the games try a download service. A good one will let you have unlimited downloads for a small one-time fee. You can see the link below for more information.


c. Unzip the game files and save them somewhere that you can find them easily, like your desktop.


d. Plug your PSP USB cable into your PSP and your computer.


e. For PSP games- go the the root directory on your PSP then make a folder called ISO. (If you downloaded PSOne games, go to the root directory on your PSP and find the folder called PSP/GAME.)


f. Copy the PSP game files into the ISO folder. (Copy PSOne game files into the PSP/GAME folder.)


Once this is done you can now play games on your PSP.

The above mention technique would help you unlock your PSP and the cheat codes.

Regards

Mar 21, 2010 | Sony PlayStation Portable (PSP) Console

1 Answer

EDGE.DAT tidak menemukan keeps poping up


Have you installed the latest firmware from the root of your memory stick? if not then go to www.edge-ds.cn and download the latest firmware, extract, then copy the files to the root of your memory stick, it should work

Jul 31, 2009 | Nintendo Revolution Console

4 Answers

I've downloaded a firmware update for my Aquos BD- HP20 Blu-ray player.  Unzipped the zip file and I put the .RVP file onto a Sony memory stick but when I try to get the player to recognize I file on the...


today i solved following errors on sharp blu-ray hp20 when updating software to play quantum of solace:

can't detect software: due to .rvp file being inside a folder--not in root directory on usb stick

more than one software file detected by player: .rvp hasn't been properly unzipped. the 2 gb disc and, as far as i could tell, my system (imac os 10.5.6) showed successfully extracted SINGLE file ready for transfer to dvd player, but dvd player said that there was more than one file. erased the 2 gb disc with disc first aid utility as part of exercise. also verified FAT format on 2 gb disc. only after i used a downloaded free mac utility *specifically for extracting ZIP files* to transfer the .rpv file to the 2 gb disc did the dvd player recognize the file and i successfully updated the player's software! (sorry for the run on, i think the logic is accurate)

Jan 29, 2009 | Sharp AQUOS Blu-ray Disc Player

1 Answer

Problems playing downloaded games(cso files)


This problem occurs when there is some problem with the firmware, it can be happen If you are running official sony firmware, and/or if your firmware in custom OE/SE, you will need UMD inserted for execute devhook app. if so, i recommend you to upgrade your firmware to use the latest version of the custom firmware. 3.71 M33-2.you can activate the plugin for using M33 or Sony-NPL9960 driver. see here for guide. but what version is your psp?

Please let i know if you experience any problems in the future. I hope i can make the appropriate adjustments, so do not hesitate to contact me if you have any other questions.

Oct 30, 2007 | Sony PlayStation Portable (PSP) Console

Not finding what you are looking for?
Sony Cyber-Shot DSC-F828 Digital Camera Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Cameras Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Ngoro

Level 3 Expert

3112 Answers

Harrie

Level 3 Expert

6746 Answers

Are you a Sony Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...