Question about Krups GMA1-42 Power Xtreme VI Work Top Blender

1 Answer

Hello, I ordered a replacement coupling gear(?) and need to figure out how to replace it. This is the little grey plastic gear that attaches to the base unit causing the blade to spin. Here are some numbers on the packaging for the part: 8090698195 and MS-0698195 Thank you, Mary

Posted by mollisu on

Ad

1 Answer

jsnweed

  • Level 1:

    An expert who has achieved level 1.
    Habit-Forming:

    Visited the website for 3 consecutive days.
    New Friend:

    An expert that has 1 follower.
    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 2 Answers

Hope you have solved your problem by now, but put a flathead screw driver in the bottom of the blender to hold the blender shaft in place then turn the gear by hand or with a plyers and it should just screw off, it is reverse threaded...

Posted on Aug 14, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a replacement chopper bowl lid for a Braun mr 6550 hand blender. I am based in the Midlands in the UK. Does anyone know where I can get one before Christmas?
Hi christine,
go to this link it might help out ..
replacement chopper bowl lid for Braun mr 6550 hand blender Google Search ..
or you could try ebay..

Sep 28, 2017 | Blenders

1 Answer

Black & Decker blender BL1900/550W, 120V-60HZ,27FM Lost the rubber/plastic seal to bottom blade that keeps it from leaking. Need replacement grey ring seal. Where can I get one in Raleigh, NC 27614...
my B

Aug 04, 2010 | Black & Decker BL550 ProBlend Work Top...

2 Answers

The plastic base the blades are fitted in ,cracked need to order replacement
the part is Black and Decker Blender Base Collar Ring BL5000-11
However these are prone to cracking. I ordered a second after my first cracked, and the second one cracked after just a couple uses.

Jun 09, 2010 | Black & Decker BL1900R Blender

2 Answers

Plastic pieces on glass jar and base are worn out and shaved down
I did the same thing. Order parts at thegourmetdepotco.com -- This problem is caused when you put the rubber gasket underneath the blade instead of above it. This causes two problems: 1. It lifts the teeth on the jar away from the teeth on the drive gear, which can grind down and break off the teeth, and 2. If the drive gear contacts the rubber gasket, it will melt the rim of the drive gear. In the future, to reassemble the jar after cleaning, first put the rubber gasket on the jar, then the blade, lastly screw on the base ring.

Apr 19, 2009 | Margaritaville Frozen Concoction (DM1000)...

2 Answers

Krups 239 blender drive gear.
Like you, I am all for repairing and keeping the world free of blenders that only need one part replaced. The rubber coupling was easily ordered online, the challenge I later found was to remove it without losing my sanity. After messing up the side grill of the blender pretty good, I realized there is an opening on the motor casing that allows access to a "gear" that is firmly attached to the axle where our little friend will hopefully screw on and restore the contraption to a working state. In order for you to see (which I must warn you, it's not much of a view) through the grill you will need a flashlight or book light. Towards the top of the aforementioned gear (not the rubber part) there is a groove in which a flat screwdriver can easily fit immobilizing the axle and allowing you to easily unscrew it. Oh, but wait, I forgot this is the faulty part and it will spin without the slightest torque on the axle thus never loosening or getting it unscrewed. My solution to this problem was to surgically remove as much rubber as possible to allow me to attach my vise grip to the nut and finally put this thing out of its misery. Using the same procedure of inserting the screwdriver to immobilize the axle I was able to screw the new part and voila the blender is fixed!!!!

Apr 08, 2009 | Krups 239 Power X Plus Work Top Blender

1 Answer

Philips Hand blender
My wife picked ours up at a rummage sale, and we've grown to love the little thing for making single servings of banana milk shake. (half a frozen banana, cover with milk, a drop of vanilla, and about one minute with the hand blender blade!) When my youngest boys dropped ours, I gathered up the pieces of plastic that connect the attachments to the motor shaft, and carefully super glued them together. I then wrapped the plastic piece with fine nylon thread and a thin layer of super glue and placed it back onto the motor shaft, then let it sit for 24 hours. It is now permanently attached to the motor shaft and good to go. Too bad Philips doesn't care enough to support their customers with a part their engineers designed to break and save the rest of the product. I'll remember this about Philips products when I buy an HDTV.

Aug 14, 2008 | Philips HR1358 Handheld Blender

1 Answer

Hamilton Beach blender rubber drive removal
plz cont -23051554 \ 23095757

Aug 03, 2008 | Oster 4134 / 4126 Classic Beehive Work Top...

1 Answer

The blender coupling on my oster snapped in half. I have the replacement part already I just cannot figure out how to get the broken coupling off the base of the motor. I also got a replacement square...
10-01-2009 Sara - see solution for rlaymon 1-9-08 "Top part of base broke off" by TanyaCS on 1-20-08 - good ideas. I just fixed mine - 2 hour job + half hour to put a new cord in. Like TanyaCS my broken coupling was rusted to shaft - used WD-40 twice and let sit - meanwhile took out motor and removed fan - kept screws and washers in order on workbench (kitchen counter) - the fan hole is "D" shaped - fan end of shaft also "D" shaped - I filed a "flat" on the other side of the factory "flat" (side of 'D' that is straight) - Used big pliers on broken coupling and adjustable wrench on on the "flats" on fan end of the shaft. Broken end came right off. New cord is 18 gauge extension cord capable of at least 6 amps. Cut off the un-needed end. Or order a replacement cord $4 when you order the rubber drive coupling $4, pin with slinger washer $3. Bet you also need new rubber feet - didn't buy for mine - wish I had. Bert

Jul 11, 2008 | Oster 465 Work Top Blender

2 Answers

Krups 572 Power Xtreme VI Work Top
Repairing the blender:
My guess: You worked the motor too hard on your last blending session and it overheated. That will cause a thermal fuse inside to cut off. The blender won't work again until you replace the fuse but otherwise it should be fine. The fuse looks like a white diode and it will be attached tightly to the motor with a nylon strap (so that it can pick up the heat of the motor). The leads to the fuse are shielded with heat resistant nylon wrap. You will need to remove the rubber drive gear in order to remove the plastic house so you can work, although if you are really handy you might be able to at least test the unit by only removing the plastic bottom on the base unit.

To remove the plastic housing, remove the little rubber feet and then remove all of the screws on the bottom of the unit. You may need to buy a bit set for tamper resistant screws (I ***hate*** those), I don't remember. When the bottom is removed, you will see that the there is a screw head on the bottom of the central motor shaft. You can use a screw driver here to hold the motor from turning, then you can carefully use a pliers to unscrew the rubber drive gear on the top of the base unit (try not to damage the rubber). With the gear removed you can get access to the wires.

To test the fuse unit, just check its continuity. Short=good, open=bad. To further test, short out the fuse with a jumper cable and your blender should work.

EPO (Electronics Parts Outlet) in Houston, TX, has the replacement fuse unit. I don't know that they like mail order.

May 13, 2008 | Krups 572 Power Xtreme VI Work Top Blender

6 Answers

How to replace the rubber drive in Krups 572?
it's not easy. you will need a set of pliers, a flathead screwdriver, and a phillips screwdriver. first, remove the 4 rubber plugs from the bottom of the blender (just work them out with your fingers). second, use the phillips screwdriver to unscrew the 4 screws that were under the ruber plugs. the blender should come apart. right in the bottom center on the inside of the blender you should see a steel rod with a groove in it. this rod will run all the way to the top and be connected to the rubber gear drive on top. get a firm grip on the rubber gear drive with your pliers. place the flathead screwdriver into the groove of the steel rod and unscrew. it will be very tight, but eventually, it will give. you will most likely destroy the old rubber gear drive in the process, but the idea is to replace that one anyway. good luck!

Q. Mosley

Jun 09, 2007 | Krups 572 Power Xtreme VI Work Top Blender

Not finding what you are looking for?

View Most Popular

GMA1-42 Power Xtreme VI Work Top Blender

  • Blenders

Related Question

I need a replacement chopper bowl lid for a Braun mr 6550 hand blender. I am based in the Midlands in the UK. Does anyone know where I can get one before Christmas?

  • Blenders

Open Questions:

0 Answers

how to put a kambrook 600w power drive back together

Feb 12, 2013 | Krups GMA1-42 Power Xtreme VI Work Top...

0 Answers

how to disassemble krups gma1 blender

Jan 06, 2013 | Krups GMA1-42 Power Xtreme VI Work Top...

0 Answers

My blender is leaking - really! Water placed in it with the bottom securely sealed leaks starting immediately.

Nov 16, 2010 | Krups GMA1-42 Power Xtreme VI Work Top...

0 Answers

how to put back together a blender

Nov 25, 2009 | Krups GMA1-42 Power Xtreme VI Work Top...

See all Krups GMA1-42 Power Xtreme VI Work Top Blender Questions

Related Topics

Krups GMA1-42 Power Xtreme VI Work Top Blender Logo

544 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Krups 572 Power Xtreme VI Work...

Krups 572 Power Xtreme VI Work...

Krups Blenders

Krups 574 Power Xtreme VI...

Krups 239 Power X Plus Work Top...

Top Krups Blenders Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

61131 Answers

ray gallant

Level 3 Expert

71004 Answers

Are you a Krups Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...