Question about Kyocera KM-1505 Copier

1 Answer

Km2030 showing code c610 - Kyocera KM-1505 Copier

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 304 Answers

C610 Broken fixing heater wire
• Warm-up does not end within 90 s.
• The secondary stabilization fixing
temperature drops to 100°C/212°F or
• The fixing temperature remains below
40°C/104°F for 7 s or longer after the
fixing heaters have been turned on.


  • Fixing heater installed incorrectly (Check and reinstall if necessary.)
  • Broken fixing heater wire. (Check for continuity. If none, replace fixing heater.)
  • Poor contact in the fixing unit thermistor connector terminals.(Check the connection of connector CN12 on the main PCB and the continuity across the connector terminals.Remedy or replace if necessary.)
  • Broken fixing unit thermistor wire.(Measure the resistance. If it is ∞ ?, replace
    the fixing unit thermistor.)
  • Fixing unit thermistor installed incorrectly.(Check and reinstall if necessary.)
  • Fixing unit thermostat triggered.(Check for continuity. If none, replace the
    fixing unit thermostat. Check the operation of the cooling fan and repair if necessary.)

Posted on Jul 09, 2011


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

CS-2030 C610 error code

Press 1087 1087 until machine shows U000. enter 163 press start. scroll to execute then press seart

Feb 22, 2011 | Copystar CS-2030 Copier

1 Answer

MITA copier DC-2360, error code C610, fuser replaced. How to reset the error ?

IF you have corrected the problem that caused the C610 (broken fixing heater wire), then the error is cleared by turning the machine power switch off then back on.

Jan 07, 2011 | Kyocera Mita Office Equipment & Supplies

1 Answer

What is the unlock code for a pantech c610 the sim card is locked

the unlock code for any phone is the last 4 digits of your phone number

Apr 19, 2010 | Pantech C610 Cell Phone

1 Answer

Dell latitude c610 screen just shows pixles moving around display is gone, even when docked on screen. thought the lcd was bad but a monitor hooked shows the same thing. Is the moboard bad?

Yes if external video output shows same defects (pixelation problems or random color squares) this is most likely an internal Video adapter issue (usually part of the system board).

After you just turn on the laptop, if you can see the DELL logo, keep pressing F12 and see if there is an option for Diagnostics...if so, this will run a quick hardware and video test, usually resulting in error codes and cause of the issue. If you experience the display problem during the startup (POST) process as well, then definitely internal video issue.

Depending on age and popularity of your model, a new system board can cost from $150-600 plus labor to install it.

Feb 17, 2010 | Dell Latitude C610 Notebook

2 Answers


You have blown your thermal fuse, causing an open circuit.

You have to remove the fuser and remove the thermal fuse. It is very easy to get it, it looks like a round black stump with a shiny bottom with 2 space terminals at each end, the bracket should be white, you cant miss it.

remove the thermistor and throw it hard on the concrete outside, you will not break it, what you are looking for is to make it rattle again, once it rattles again, re-install.. and clear the error code..

To do this you will have to do the following;
Press 'stop/reset' then 'start' then left copy exposure button and hold them all down. This will enter simulation/tech mode.

Enter '163' you do this by pressing the + and - buttons (zoom buttons)

'CLE' should show up (Clear)

then press start.

Reboot the machine and you away again.

Oct 13, 2009 | Kyocera KM-1505 Copier

2 Answers

Code erreur

c610Bitmap (DIMM) problem

Sep 08, 2009 | Kyocera KM-1510 Copier

1 Answer

Dell Latitude C610 doesn't recognize hard drive

when you took out the old hard drive
there is a black hard drive connector
this would have holes to push on to the new hard drive
without this, it will not plug into the motherboard
be careful if one of the pins breaks the hard drive wont work

Jul 21, 2009 | Dell Latitude C610 Notebook

1 Answer

Dvd wont read

have you got any error codes showing, i had error code 10 on my dell 1720, i removed the upper and lower filters, now my dvd drive works fine

Jan 15, 2009 | Dell Latitude C610 Notebook

1 Answer

Dell battery problems

1. Needs to be replacing the charing (L) coual.

Mar 24, 2008 | Dell Latitude C610 Notebook

Not finding what you are looking for?
Kyocera KM-1505 Copier Logo

Related Topics:

1,059 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers


Level 3 Expert

1363 Answers


Level 3 Expert

85223 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides