Indication is INK TONER WASTE BOX FULL Not sure what to do, if any thing? Al

Typically you will need to replace the waste toner box. There is usually a difficult to access part of the bottle that is used by an optic sensor to tell when the box is full. Plus toner is very fine and you do not want it getting into the air. Toner will pass through the filter of most vacuums and go back into the air.

When you removed the waste toner bottle, there is a sensor inside the copier. When you remove the waste toner, look to the opening where the top of the waste bottle was, clean that area and return the bottle and turn the copier OFF then ON. Good Luck

The clear section of the waste toner box where that goes inside the machine check that area sensor located there might have toner on it so the printer thinks the waste toner box is full

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

REPLACING THE WASTE TONER BOX
The waste toner box collects residual toner that is produced during printing. When the used toner box is full, the display
will show "Replace used toner container". Follow the procedure below to replace the used toner box.
Open the front cover.2
Release the used waste toner box.
The waste toner box will fall forward as shown.
Gently support the box with your hands as you let it fall forward
as far as it will go.
Remove the waste toner box.
Hold the box by both hands and lift it up slowly.
If the waste toner box falls too far forward, it will not be possible
to remove it. (Remove the box when it is at an angle of about
30 degrees.)
Install the new waste toner box.
Insert the box from above at a slant. (The direction opposite to
when you removed it.)
Push the waste toner box into the
machine.
Push the box in until it clicks into place.
Close the front cover

Hope this helps.

The waste toner box is located on the right hand side of the printer. There is a door/cover that opens up on the right side. It is a milky white plastic container. Check to make sure it is there and installed properly and the door is fully closed. If all that is correct it my be full.

There should be a new waste toner container in the toner box (along with a toner). The toner and waste toner are normally replaced at the same time.

If you don't have a new waste toner container you can tray emptying the one that is in the printer BUT be very careful. The toner is a fine powder and can get all over if spilled. If you ever spill toner never use water or any other liquid to try and clean it, that will just turn it to a liquid ink.Brush it off your cloths and vacuum it up.

If you do try and empty the container and the machine continues to tell you it needs to be replaced it can be because there is still toner on the inside of the toner container and the sensor is seeing it there.

I hope this is helpful,
Shawn

remove the waste toner device ..and clean it ..or replace it ...after that when you put it back ..get into the maintenance menu and reset the waste ink ...and you will be ready to go ..Check the manual cause all these things are explained there ..

Printers have waste ink/toner boxes/tanks, when they are full, you need to empty them and reset the warning notice. You may need to take it to a service centre if it is a proffesional model

make sure all the toners are ok and there is no dust inside i mean waste ink powder. remove all the toner and shake it and install it again.

Remove the developer and toner cartridge from the front of your unit. This will allow you to take out your drum where your waste toner box is. Once you have your drum with your waste toner box make sure to detach the waste toner box from the drum. Take a damp linen free cloth and wipe down the inside of the drum unit where your waste toner box goes in. Now take your waste toner box and make sure to secure the waste toner box really well to the drum. This has to be in very tight or else the printer will not think that there is a toner box attached the drum and this error will continue to appear. Important thing is to make sure that the toner box is attached really well to the drum unit.

Several things. When the drum unit has toner backed up in the waste toner channel, it will put a drag on the drive assembly. Make sure the waste toner reservoir in the toner unit is not filled up. If it is, take the toner unit out, open the spring loaded waste door and try to vacuum or dump out the toner. Do not use a regular home vacuum inside your house. the toner is too fine and will disperse throughout your home and possibly cause some breathing irritation.

I’m happy to help further over the phone at https://www.6ya.com/expert/jayw_0e86fb055a7b73de