Washer won't start. Power is on, pressed power, then pressed permanent press, then water temp, then start. There is a red light on spin cycle and it just beeps and doesn't start.

1 Answer

James Foster

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Novelist:

An expert who has written 50 answers of more than 400 characters.
Expert
251 Answers

Hi - if that red led light comes on as you press start - then the display module is faulty - however it's not always the case - often its the motor controller module thats faulty..

Your call - display module first and hope it works or controller.

The manufacturers recommended procedure is to replace the display module (primary) if it still doesnt work then replace the control module (secondary).

Cheers

Posted on Jun 27, 2011

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

MAYTAG WASHER 2000 SERIES E1F6 CODE COMES UP OLUTION PLEASE

"LF" on display (Long Fill - no water or insufficient water supply) Press POWER/CANCEL to cancel the cycle. Unplug washer or disconnect power.
Plug in washer or reconnect power. Re-select cycle and press START/PAUSE. "F9E1" on display (Drain Problem) Press POWER/CANCEL to cancel the cycle. Unplug washer or disconnect power.
Plug in washer or reconnect power. Re-select cycle and press START/PAUSE. "SD" on display (Suds Routine) When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. "SD" is displayed during rinsing and at the end of the cycle to inform you that the Suds Routine was activated. Use only HE (High Efficiency) detergents. "F--E--" Variables (Washer Problem) Press POWER/CANCEL to cancel the cycle. Select RINSE, DRAIN & SPIN if there is excessive water in the washer. Re-select cycle and press START/PAUSE.

Read full answer

Dec 22, 2018 • Maytag Washing Machines

0helpful

2answers

Model gltf2940fs clothes still wet only after the perma press cycle

Good Afternoon Friend,

I understand that your clothes are still wet in your Frigidaire washer, model# GLTF2940FS, but only after the perma press cycle. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Sometimes there can be a miscommunication between the different boards inside your appliance. Restore power and try the perma press cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Read full answer

Jul 01, 2014 • Frigidaire GLTF2940ES Front Load Washer

1helpful

1answer

My Fisher & Paykel 708 smart drive washing machine won't starts and beeps.

That is Error code 9
9. (00001001) Phase 1 to 5 - Size Error
Phase 4 to 5
The Display size switch setting does not match that stored in memory.
Action - Reselect the size of Smartdrive by using the SIZE SETTING MODE. Push and hold
the water temp up button, then press the power button to enter SIZE SETTING MODE. Three
LEDs are used to identify size. The cold water temperature LED identifies 5kg. The low water
level LED identifies 6kg. The hold spin speed LED identifies 7kg. If the product has not been
setup before all 3 LEDs will be on. To set the size for 5kg push the wash temp up button then
the power button. To set the size for 6kg push the water level up button then the power button.
To set the size for 7kg push the spin speed up button then the power button. This locks the size
into memory. To check the size is set, start a cycle.

Read full answer

Dec 20, 2012 • Fisher and Paykel Washing Machines

0helpful

2answers

Start button blinks; won't empty; won't leave wash cycle

turn your dailer to spin cycle

Read full answer

May 21, 2012 • Whirlpool LHW0050PQ Front Load Washer

0helpful

1answer

Washer Control Locked blinking and won't washer won't work

Water still in the bottom of the drum. Empty, clean filter and check pump is turning. Once pressure switch is satisfied no water is left it'll allow the door to open, assuming the door interlock is still ok.

Read full answer

May 19, 2012 • Washing Machines

0helpful

2answers

We pulled our stacked washer out from the wall to service the cold water hose filter on the back of the unit. when we pushed it back into it's location the washer won't start, won't fill...

I know you don't want to hear this, but either you did something to the hose filter or you didn't get it plugged back in correctly.

If you banged the water inlet valve in moving it back, it might be damaged.

Suggest you unplug everything and start over.

Read full answer

Sep 04, 2011 • Frigidaire FEX831F Top Load Stacked Washer...

0helpful

1answer

I can't get the control panel to reset. The wash cycle light comes on but it just beeps and the dishwasher won't start. I press the start button and it stops beeping for a minute but it still...

II might need the actual model number. However, you can go to page 9 on this manual and check if the flashing options can fix the problem. I am assuming you have already tried to turn the power off and back on.

The ohter thing to try is the reset sequence. Within 6-7 secs press High Temp/ Heat Dry/ High Temp/ Heat Dry/ High Temp/ Heat Dry. All lights should light up, press Start button to exit.

Read full answer

Jun 24, 2011 • GE Nautilus 24" Built-in Dishwasher

0helpful

1answer

Hello, Re: frontloading washer Model C45172 Our washer has been operating withiout hitch since purchase about five years ago, We love it. Today I tried to program it to do an extra rinse after wash...

For the Elite (HE) machines:

Press 'STOP' twice, press 'POWER', choose a wash cycle (such as 'NORMAL'), select wash options (water temp), press 'START' to finish the reset sequence.

Other Kemore electronic washers:

Unplug the machine for a minute, plug it in. Press 'PAUSE/CANCEL' twice.

Good luck from Detroit, MI.

Read full answer

Jun 12, 2011 • Kenmore Washing Machines

0helpful

1answer

I have a front load GE Adora washer and it stops in the middle of the cycle and the start/pause button blinks. I press the blinking button and it goes for a little while longer and then stops again with...

How to clean the filter

Technician's Service manual

I believe your pump filter is clogged. Use the links above to help you save some money.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Read full answer

Jun 03, 2011 • General Electric WCVH6600H Front Load...

0helpful

1answer

Control lock light will not go off.

Do you have any error codes?

Does water remain in the washer after the final spin?
If water remains in the washer after the final spin, then the door will not unlock. Drain/Spin or Spin Only to remove any remaining water from the washer. The door should unlock at the end of the cycle.
Is the door locked and the Add A Garment light on?
If the Add A Garment light is on, then the washer door will unlock after the Pause/Cancel button is pressed once. Pressing the Start button will restart the washer at the same point where it left off in the cycle.
Is the door locked and the Add A Garment light off?
If the Add A Garment light is off, then the washer door will unlock after the Pause/Cancel button is pressed twice. The door will not immediately unlock while the cycle is running due to a possible high-water level in the washer, high-water temperature, tumbling or spinning. It may take up to five minutes for the washer to stop spinning and draining before the door will unlock. You will hear the door click when it unlocks.
If Pause/Cancel does not work: